Glen, thank you for your interest in the RIDGID 5.5 Amp Compact Fixed-Base Corded Router. This is a trim router and the base is not designed to accommodate bushing guides. Our larger routers will though. Thank you for asking, If you have further questions and would like to speak with a RIDGID Customer Experience Professional, please call, 1-866-539-1710 M-F from 9am-6pm EST. Hope this helps! - Vini

I made a base that will accept porter cable bushings. I used 1/4"-thick clear lexan. NOT PLEXIGLASS!!! Lexan is a polycarbonate similar to plexiglass, but stronger. I wanted to use a trim router that is lighter weight than my porter cable routers.

Not to my knowledge. Personally, I would contact Ridgid regarding that particular attachment

Hello Fred, the RIDGID 5.5 Amp Corded Compact Fixed-Base Router model R24012 cannot be used with a plunge base. You will need a full sized router for that application. If you need further assistance with this question, please contact RIDGID Customer Support directly at 1-866-539-1710, Monday thru Friday 9am to 6pm EST. Thanks for reaching out to RIDGID. - Eve

I have never seen that accessory for this trim router.

This is a hand-held router. Smaller in detail than larger routers that can be used with router tables.

Don't have a clue to be honest. I ended up making my own. You could check with Ridgid and see if they offer one, though I doubt it

I have never used this trim router with a router table. I use a full size Bosch on my table.

Hello Purdymay, the RIDGID 5.5 Amp Corded Compact Fixed-Base Router R24012 cannot be used with a router table. Thanks for asking! - Eve

Hello Woodman, We appreciate your interest in the RIDGID 5.5 Amp Corded Compact Fixed-Base Router R24012. We currently are not manufacturing a bushing set. We would recommend checking out compatible retailers. Our support team may be able to give you suggestions. You can contact them at 1-866-539-1710, Monday thru Friday from 9am to 6pm EST. Thanks for asking! - Eve

Mine does. I think that's "standard".

Yes, there is a light.

Hi Stephen, Yes, the RIDGID 5.5 Amp Corded Compact Fixed-Base Router R24012 has a built in LED. Thanks for asking! - Eve

Yes it has a light

When I bought my router, (same model as yours) it came with a manual that tells you. Anyway, you will need the model # and serial # to proceed. You can then go to www.RIDGID.com or call 1-866-539-1710 for the closest authorized service center nearest you.

I have been able to get replacement parts by contacting Ridgid directly in the past. If you go to the Ridgid website there are parts catalogs under Support.

Hello RobMaker, thank you for your interest in the RIDGID 5.5 Amp Corded Compact Fixed-Base Router. The barrel or collet is 1/4 in. Thank you for asking, If you have further questions and would like to speak with a RIDGID Customer Experience Professional, please call, 1-866-539-1710 Hope this helps! - Vini

Using calipers, the router without base measures 2.339 in and with base, measures 2.746 in.

It depends on the bit you are using. This is a trim router. Not a big brute. It works great for trim and finish type work. Take a look at your task. Will a smaller shank router bit work for what you are doing? It won't take 1/2" bits.

I'm not sure what you are asking. The depth of cut is determined by the length of bit you use and the setting used on the router. The depth of cut should be no greater than twice the diameter of the bit to prevent breaking the router bit.

First off it will not "cut" anything. It is not a saw. t is designed to put an edge or round over on a piece of wood, Yes you can do some minor rabbit joints, a dado etc. This is not a bench router. I have personally used it to create decorative trims and wood joinery. The typical stock used on is either 3/4" or 5/4" materials.

Depends on the length/size of bit you are using and what the material is. Remember that this is a "compact" router and intended for "trimming" formica on counter tops, etc.....it will not "hog out" a 2 inch deep cut in oak lumber.

As thick as the bit is long would be the logical answer. Now I am a professional woodworker and I use mine as a router, though if I were planning to cut wood with a router, this one definitely has the power and is easy to hang onto.

Hi Mike, Thanks for inquiring about the RIDGID 5.5 Amp Corded Compact Fixed-Base Router R24012. This router cannot be used for cutting. If you need further assistance with this question, please contact RIDGID Customer Support directly at 1-866-539-1710, Monday thru Friday 9am to 6pm EST and follow the prompts for Technical Support. Thanks for reaching out to us. - Eve