Return this item within 90 days of purchase.
Get an answer now with AI
Magic Apron Assistant is an AI virtual assistant. By proceeding, you consent to the recording and use of your information by The Home Depot (and authorized third parties). More information
DIG's 1 GPH Button Barbed Dripper that comes in packs of 10 is easy to open and take apart for cleaning. The dripper features labyrinth water flow paths that allow for a consistent flow rate at an incoming pressure of 15 to 25 psi with higher discharge at higher pressures and lower discharge at lower pressures. Chemical and clog resistant, the drippers are an economical choice for all type of drip irrigation installations and recommended for residential, commercial and agricultural applications. These drip emitters are a low-cost solution for an individual plant, planter boxes, rows planting, vegetable rows, small to large pots, groundcovers, shrubs and trees, low-pressure gravity feed drip irrigation installations and areas where conventional sprinkler systems are not practical. The button drip emitter is made of two-piece construction and can be taken apart for cleaning by twisting the top part of the drip emitter counterclockwise and pulling it apart.
Dimensions: H 5.5 in, W 0.5 in, D 0.5 in
Product Depth (in.) | 0.5 in |
|---|---|
Product Height (in.) | 5.5 in |
Product Width (in.) | 0.5 in |
Tubing Size | Fits All Tubing Sizes |
Color Family | Blacks |
|---|---|
Emitter Type | Button Dripper |
Irrigation System Component | Drip Irrigation Emitter |
Maximum Flow Rate (gph) | 1 |
Pack Size | 10 |
Returnable | 90-Day |
Spray Pattern | Drip |
Spray Pattern Degrees | 360 Degrees |
Manufacturer Warranty | 3 years |
|---|
Hi 3449hln: These drippers may be taken apart for cleaning by unscrewing the outlet side from the body (inlet). Hold the body stationary and grab the outlet side tab next to the outlet barb and turn it counterclockwise until it separates from the body. Then you will be able to flush and rinse it out. After cleaning, simply screw the outlet side back into the inlet body until finger tight. Thank you for the question and for using DIG irrigation products, 💧
Hi Justin: Yes, it does matter, the inlet side is the side with the single large 1/4" barb. This is the side that must be connected to the supply tubing. The outlet side is the side with the smaller barb and the handle that is used to unscrew the outlet from the body for cleaning. Thank you for your interest in DIG irrigation products!
Hi Bulldog: The answer is YES! Please see this link for more info... https://www.digcorp.com/wp-content/uploads/2023/04/DIG_Drip-Irrigation-Guide-2023.pdf Thank you for your interest in DIG irrigation products, :)
Our .700 OD tubing can support 220 gallons per hour of flow, this means you could install 220 x 1gph drippers, 110 x 2gph drippers, or 55 x 4gph drippers. You can install any combination of drippers as needed, just be sure not to exceed 220gph of flow.
The drip emitters included in the kit are our 1 gph PC drip emitters model B221B. If you have any further questions, please feel free to contact our technical service/product support team at 1-800-322-9146 or tech@digcorp.com.
Here is a blog article detailing the differences in point source emitters https://www.digcorp.com/point-source-on-line-emitters/. If you have any further questions, please feel free to contact our technical service/product support team at 1-800-322-9146 or tech@digcorp.com.
Lazy technical support.
A button drip emitter can be installed on the end of ¼” poly tubing or directly on the top or side of ½” poly tubing. The inline drip emitter is designed to be installed inline on a length of ¼” poly tubing with the end of that line capped using our G79B goof plug. If you have any further questions please give our technical service/ product support team a call at 1-800-344-1172.
There are two main differences 1. The Rain Bird 1 GPH dripper SW10 is pressure compensating, the DIG 1 GPH W22100 is non -pressure compensating 2. The DIG W22100 can be taken apart and unscrewed for cleaning, the Rain Bird cannot.
Viewing 1-8 of 9
4.4 out of 5