A: Our 1/4in barbed connectors are made of high-impact, high-strength, UV-resistant Acetal plastic that has excellent wear properties in dry and wet environments. Acetal does not contain BPA.
A: The H80B is not an emitter it is a fitting designed to connect two ¼” lines together or to connect ¼” tubing directly into ½” poly tubing. If you have any further questions, please feel free to contact our technical service/product support team directly at 1-800-322-9146 or email@example.com.
A: This piece is used to connect (or repair a hole in) the tubing. It does not "drip" as it's a steady stream, so I would recommend getting the actual dripper endpiece (they come in various gallons/hour sizes).
A: No. Your looking for 0-14 GPH, 360 Degree, Adjustable Drip Emitter on Spike (10-Pack
A: These are the barbs to link multiple drip system (1/4”) lines. If you’re looking to link two (or more) drip lines, these are what you’d use. If you’re looking for drip hose, you’dwant to look at something like https://www.homedepot.com/p/DIG-1-4-in-in-X-100-ft-Poly-Distribution-Tubing-170-ID-X-250-OD-B38100P/204184721 or https://www.homedepot.com/p/Rain-Bird-1-4-in-x-100-ft-Distribution-Tubing-T22-100SX/202078362.
A: The H80B is a ¼” barb connector used to connect two pieces of ¼” tubing or connect ¼” tubing to the side or top of ½” poly drip tubing. If you are looking for drip emitters, I would recommend models B221B, B222B or B224B. If you have any further questions, please feel free to contact our technical service/product support team directly at 1-800-322-9146 or firstname.lastname@example.org.
A: Yes! I have been using DIG products for nearly 25 years now. Those barbs work just fine. I'm older now and need help to insert them into the hose/pipe. But I solve that by carrying a mug of hot boiled water to dip the connector tubing onto the barb and/or emitters. Have fun.
A: In my opinion, no, they won’t be the dripper. These are made to connect 1/4 line.
A: leaking ¼ inch barb connection point to ½ inch poly tubing can be caused by a few factors. First you want to make sure your pressure is within 25 to 30 psi a preset pressure regulator to make sure your pressure is within recommended operating pressure. When punching the ½ inch tubing make sure not to punch at an angle so the hole does not get stretched out and cause leaking. Also, when inserting the ¼ inch barb try to avoid pushing in the barb too far into the hole to avoid stretching the tubing. In most cases any leaking from the ¼ inch barb connection point will seal on its own after a week or two of operation. We do also make a self-piercing ¼ inch insert connector model D5010 that may work better for you. If you have any further questions, please contact our technical support team at 1-800-322-9146.
|Name||1/2 in. Barbed Tees (4-Pack)||1/4 in. Barb Connectors (50-Pack)||1/2 in. Barbed Elbow, 600 in. ID, 17 mm, BRN (20-Pack)||1/4 in. Barb Tees (100-Pack)|
|Fitting Type||Barb Fittings||Barb Fittings||Barb Fittings||Barb Fittings|
|Connection||Comp||Barb x Barb||Barb x Barb||Barb x Barb x Barb|
|Drip Irrigation Fitting Component||Tee||Coupling||Elbow||Tee|
|Material||Plastic||ABS Plastic||ABS Plastic||ABS Plastic|
|THD SO SKU||1000650704||531677||531677|
|View Product||View Product||View Product||View Product|