Questions and Answers for Orbit O-ring and Rubber Hose Washer Combo 12-pk Hose and Sprinkler Repair

A:  Not likely. There are no P65 warnings on the packaging no in the website descriptions

A:  contact manufacturer;if liquid gasket ,be more concerned with bonding agents and contact with drinking water.

A:  I simply press the ring off of the stick/hanger, but it does take some force. Then, I can replace it and reuse it.

A:  Fold the round end of the holding package and take what you need and unfold it again. Have a nice day with JESUS! Thanx..........Tony..............>)))*>............

A:  best advice is see if store has digital caliper and measure inside diameter, i.d. and outside diameter,o.d. sometime its a trial and error at home .and save receipt. goodluck

A:  Gus, that might be a question for Ray Padula. All we can say is that these washers and O rings are built for use with 5/8" - 3/4" standard hose connections.

A:  Sorry, I do not know the technical part of this product. Just a user. By the way, I don’t use it because it has no steam for my flowers.

A:  Gus, that would be a good question for the Ray Padula quick disconnect product page. These hose washers are designed for use with standard 5/8" - 3/4" hose connections.

A:  Just place an order to have it shipped to the store.

A:  talk to pro desk for custom order ;check inventory

A:  They should be restocked by now. If not, the Dept. Manager would be happy to order them for you to pick up in store.

A:  I think you should call your local store about this.

A:  No, they are not for use in the same fitting at the same time.

A:  No! you'll only need one of the two, not both.

A:  no

A:  You can use them together or separately.

A:  No, depending on the attachment you have, one will fit and seal better than the other. A lot of the simple squeeze handle sprayers use the flat washer. If you still have the seal that was in there, replace with whatever was closest. If you don't, just try one type at a time and see if it seals well.

A:  The washers are for most hoses. The rings are for most hose reels. They are the two most common serviceable parts on an outdoor hose. You should be able to match them up to the old washers/rings

A:  None of them fit my hose, so I never used any of them.

A:  NO......Use either but not both. Replace old washer with new washer, etc. Replace O Rings with new O Rings. Both are included for your convenience.

A:  Yes, who doesn't?

A:  Using both it will never seal properly.the hose washer and O rings are only for different types of applications and used separably. .

A:  yes, but that was not my concern.

A:  Mike0, as long as the hose is 3/4" garden hose thread, yes these Orbit o-rings can be used for that purpose.

A:  The o-ring fits over the inside stem of the hose nozzle. If you remove the nozzle from the hose and screw it all the way out, the inner stem will come out and you'll see the o-ring. When you close the nozzle, the o-ring seals against a seat in the outer part of the nozzle, preventing water from coming out.

A:  I use as it as washer when my faucet nut is a bit deeper that needs ticker washer.

A:  The description of the product states: "O-rings allow for maximum sealing performance" So, perhaps the O-rings are used when the washers don't provide a sufficient seal.

A:  quick connect items,kitchen faucet bases,and some people wear as rings and bracelets.

A:  the O-rings are for where the hose receiver goes inside the rotating reel. disassembly required.

A:  The O-Rings are internal. Just one inside a brass sprayer nozzle. That seals the water from leaking out onto your shoes. Other sprayer "may" have an O-ring. IF it starts leaking from the top end, take it apart if you can. Most chances there will be an O-Ring in there :)

A:  Try not to use two O-rings at once, touching each other. Just use one. I usually start with the flat design, tighten by hand, and if it leaks water, remove the flat and try the round. One of the two should work. They do go bad after a year or a few years, due to weather damage. Try not to overtighten with a tool, just use hand tight. Good luck or hope you already found the answer!

A:  only one choice;connect water to the female side and connect the male side to the female adapter on feeder

A:  I bought the O-rings to fix a wall mounted reel. It did no fit.

A:  Rich, the LHR002 seems to be a hose reel cart, and doesn't include a hose. That said, three of the most common washers are included in this pack. Most 3/4" hose washers are compatible with most 3/4" product and hose. Please contact our Support team at 1-800-488-6156 if you have further questions, and we'd be happy to help in any way we can. Thanks!