Q:This works great but it will not set to the alert. It only works on the alarm. Is there a way to fix it?
by|Sep 18, 2024
2 Answers
Answer This Question
A: Below is a link to the installation instructions and user manual.
https://images.thdstatic.com/catalog/pdfImages/5c/5c13211c-82d8-4c75-a9ab-73f90a54d86c.pdf
Mike
by|Sep 19, 2024
A: Hi Suzie
as in the previous question, please contact us.
by|Sep 20, 2024
Q:Can the Motion detection range be reduced to 15 feet? I don’t want it ringing constantly for people walking on common area path 2) when sounds off, does it need to be manually turned off or stop on own after a couple mins? Thx
by|Sep 1, 2024
1 Answer
Answer This Question
A: Hi
The range cannot be reduced, but you can tilt it down so that the angle hits more to the ground. The buzzer will automatically shut off after a preset time.
by|Sep 3, 2024
Q:Can the sound (alert) level be adjusted? I want to scare animals away from flowers.
by|Jun 7, 2024
1 Answer
Answer This Question
A: Hi Karen
This is a motion sensor only, not an alert system, and it does emit any sounds, it requires a receiver inside the house. Please read further down on product details.
by|Jun 8, 2024
Q:Does it require batteries?
by|Jan 18, 2024
1 Answer
Answer This Question
A: Yes, requires a 9 VDC battery (not included)
Please note that this is not a stand-alone system, but an add on to an existing system
Works with household alert receiver HA-434RL only
Uses one 9-Volt alkaline battery for sensor (not included)
Receiver is powered by an adapter (included)
by|Jan 18, 2024
Q:Does any of San Diego stores have this in stock?
by|Mar 11, 2023
1 Answer
Answer This Question
A: Sorry, this only available online.
by|Mar 12, 2023
Q:I have the 4 zone base unit with one motion sensor programed onto zone one.
At various times zone 3 and / or 4 will be flashing a trip indication.
WHY?
by|May 9, 2019
3 Answers
Answer This Question
A: Regarding you issue, please refer to the following steps to reset and reprogram the sensor to the receiver unit once again.
To ERASE memory:
1. Unplug AC adaptor from the receiver.
2. Open the back cover, press and hold the “Learn button” from the receiver. Do not release the learn button until step 4.
3. While holding it down, plug in AC adaptor to the receiver. Once AC adaptor plugged in, you may release the learn button from the receiver.
To program sensors to zones:
1. The green LED will be on indicating it is turned on.
2. Press and hold the learn button for 5 seconds again, until both green LED and zone 1 red LED flash. You may now release the learn button.
3. If you would like to program the sensor to zone 1, activate the sensor while the zone 1 red LED is flashing. Press the SET button on the back of the sensor to activate it.
4. If you would like to program the sensor to other zones, press the learn button again after pressing to zone 1, until the red LED flashes at the zone you want to program the sensor to, then activate the sensor.
5. Once the sensor is programmed, the green LED will be steadily on and none of the red zone LEDs will be on.
by|May 13, 2019
A: birds and even the sun occasionally causes false trips
I even have one squirrel that likes to watch the light flash as he gets close to the sensor
by|May 21, 2019
A: the correct answer is listed, reset the sensor,using the instructions listed, I accidently set one sensor to both spot 2 and three, Since another sensor was also in spot two when the number three sensor would trip it would also light the light on spot two , After resetting all the sensors I have had no other issues, except I also have a squirrel who thinks the sensor is a mirror and likes to watch it blink.
I love my system and it alerts me when someone comes in any of my multiple driveways , with corresponding beeps associated with that driveway sensor. Sure saves me a lot of unexpected guests.
I also have the house next door alarmed and it alerted me to squatters who thought they could sneak in and live rent free. I got them out in time to prevent an evection requirement. That alone was work way more than the cost
by|May 29, 2020
1 found this answer helpful
Q:From January 14, 2019 Answer:
If HA-300 kit and HA-434TL sensors are the same with the same specs. What power supply would each sensor use.
by|Jan 14, 2019
2 Answers
Answer This Question
A: The motion sensor from the HA-300 kit and the motion sensor model HA-434TL are the same with the same spec.
by|Jan 17, 2019
A: This motion sensor operates by battery.
by|Jan 19, 2019
Q:What's the difference between HA-434TL & HA-300. How are these two sensors powered.
by|Jan 13, 2019
1 Answer
Answer This Question
A: The model HA-300 is a kit, comes with 2 motion sensors and 1 receiver and the model HA-434TL is only a sensor. Therefore, both motion sensors are the same.