Return this item within 90 days of purchase.
Get an answer now with AI
Magic Apron Assistant is an AI virtual assistant. By proceeding, you consent to the recording and use of your information by The Home Depot (and authorized third parties). More information
BrassCraft 1/2 in. Nominal Sweat Inlet x 3/8 in. O.D. Compression Outlet Multi-Turn Straight Valve controls water flow to household plumbing fixtures - faucets, toilets, dishwashers, icemakers, washing machines, etc. The straight valve is most often used where the water pipe enters the room from the floor. With a few turns of the valve handle, you are able to stop the flow of water leading to the plumbing fixture, allowing for maintenance and repair without turning off water to the entire home.
Inlet Diameter (In.) | 1/2 |
|---|---|
Outlet Diameter (In.) | 3/8 |
Product Length (in.) | 2.75 in |
Application | Potable Water |
|---|---|
Color/Finish | Silver |
Compatible Pipe Material | Copper |
Compatible Product | Faucet, Other, Toilet |
Connection | Sweat x Comp |
Features | Lead Free |
Indoor/Outdoor | Indoor, Outdoor |
Material | Brass |
Maximum Pressure (PSI) | 125 PSI |
Maximum Working Temperature (F) | 160 |
Pack Size | 1 |
Returnable | 90-Day |
Valve Configuration | Straight |
Manufacturer Warranty | Limited Manufacturer Warranty |
|---|
Sweat inlet multi-turn straight and angle valves have a metal stem that is made out of brass.
Thank you for your question. We would require more information to determine if our water stops is designed for that use. Please contact our Customer Support Team at 877-277-7755 and reference this review.
NO PLEASE DONT EVER USE THIS FOR GAS
Hello, Thank you for your question. We would require more information to determine if our Connector (or other product) is designed for that use. Please contact our Customer Support Team at 877-277-7755 and reference this review.
Yes
IF the body of the valve is in good condition, it is possible to buy a replacement valve, remove the handle, remove the nut, and replace the valve stem (after turning off the house water supply). The stem (or the rubber washer on the tip of the stem) is usually the only reason one of these valves has a problem. If you replace the stem, you are replacing the washer, stem, bonnet washers and handle. I did this when the washer on my kitchen shut-off valve (25 years old) was showing up in the screen of the aerator. That replacement was a lot easier than replacing the entire valve with a blowtorch under my kitchen sink. I just bought 5 of these to replace the valve inner parts on a 50-year-old house. The valves are attached to iron pipe, and I bought the sweat type valves because I do not want to install plastic stems.
Yes, may have to add a small extension piece on the copper piping to accommodate the cutting off if the other one...but if you have basic knowledge of sweating pipes together it should be no problem
Yes, if the shutoff valve for your house works, and you have the tools and supplies (torch, solder, flux, pliers, wrenches) necessary, and the skills to solder the valve in place, without setting the house afire. Go for it!
Hello Daniel - Thank you for your question. On The Home Depot website there is a video shown with this product is to help you with installing your new valve . This video is includes information that might be helpful if you have to change out the water stop to support a dishwasher as well as standard information for other water applications. Please contact our Customer Support Team at 877-272-7755 if you have any other questions.
If you know how to solder (sweat) valves onto copper pipe it is easy. However, if you don't have a butane/propane torch, solder and flux, it can be tough. I've also used "BrassCraft 1/2 in. Nominal Compression Inlet x 3/8 in. O.D. Compression Outlet Multi-Turn Angle Valve Model# OCR19X C1" which only requires two wenches which is really easy. I have both in my house and both are working well.
No it is not easy to replace. Removing the valve from the attached fitting requires two wrenches and a lot of work. Then you have to doubly make sure it doesn't leak. To avoid the leaking problem. (Since the old valve is already installed) I usually just take out the handle and stem and put the new handle and stem from the new valve in its place. Make sure the black gasket is still attached to the stem. If not you will have to remove the gasket out of the old valve body. If not already in place I will put in a new flex hose. These are quick to install and I have never had one leak on me. I can usually do this in about 15 minutes.
As long as you have a torch and basic knowledge of plumbing you will be able to complete this job.
Yes it can be easy to install but you have to be aware of what you are doing and what exactly needs to be done.
If you know how to sweat a pipe, then yes it's relatively easy.
Yes, it's a good idea to do that since if it gets overheated the black grommet may be damaged.
Yes that is the best way to do it. Just below the handle you can use an adjustable wrench to unscrew the valve and seat before sweating it on to the pipe.
Yep. It's pretty easy too.
WaterMan, Thank you for your question. Indeed, you can remove the guts of this BrassCraft valve for sweating. But it is not required for installation. You can sweat the valve with it on the open position. Please also note that the bonnet nut should only be tightened enough not to leak. If over- tightened, the valve handle will be difficult to turn. If you have any other questions about BrassCraft valves, please do not hesitate to contact our product Experts toll free at 877-272-7755
Absolutely it can. Remove also the compression nut/ring from the top. Put the thing on a vise grip or just use a second #2 adjustable wrench to hold it tight; then use the wrench #1 to unscrew that nut along with the handle. Do a thorough job of cleaning up the connection inside with the wire brush before actually sweating it. I just replaced three other competitor brand with BrassCraft.
Viewing 1-5 of 5
4.6 out of 5