#1 Home Improvement Retailer

Internet # 319621471

Model # R09895KN

Store SKU # 1007449565

18V Brushless Cordless 30-Degree Framing Nailer Kit with 4.0 Ah Battery and Charger

$389.00
Apply Now
Pay $339.00 after $50 OFF your total qualifying purchase upon opening a new card. info
Apply for a Home Depot Consumer Card
  • Drives 3 Nails per Second with Zero Ramp-Up Time
  • Includes: 4.0 Ah Battery and 18V Charger
  • Free Parts and Service for Life with Registration
  • View More Details
Store
0 in stock
icon
Free & Easy Returns In Store or Online
Return this item within 90 days of purchase. Read Return Policy
Product Details

About This Product

RIDGID introduces the R09895KN 18V Brushless 30° Framing Nailer Kit with 4.0 Ah Battery and 18V Charger. Paired with any RIDGID 18V battery, this framing nailer provides all the power of a pneumatic nailer, but with the convenience of cordless freedom. With no compressor, no hose, and no gas cartridge, this cordless framing nailer enables faster set-up and easier maneuvering on the jobsite. The RIDGID 18V Brushless 30° Framing Nailer drives 3 nails per second with no gas cartridges and zero ramp-up time, meaning that there are no delays once the trigger is pulled. To meet all professional needs, the high-strength brushless motor in this framing nailer delivers enough power to sink 2 in. to 3-1/2 in. clipped head framing nails into engineered lumber. Brushless Motor Technology delivers more runtime, more power, and longer motor life, and the ability to drive up to 750 nails per charge to keep residential contractors and remodelers focused on the job at hand. The included battery and charger are compatible with all RIDGID 18V Tools. Best of all, this tool is 100% compatible with all RIDGID 18V batteries, and with registration, is eligible for the Industry Leading Lifetime Service Agreement, providing FREE seals, FREE pistons, and FREE driver blades - For LIFE.

Highlights

  • Brushless Motor Technology delivers more runtime, power, and longer motor life
  • Drives 2 in. to 3-1/2 in. full round head framing nails into engineered lumber
  • Drives 3 nails per second with no gas cartridges and zero ramp-up time
  • 750 nails per charge when using the included 4.0 Ah battery
  • Selectable mode switch allows contact actuation or single sequential actuation mode
  • Tool-free depth of drive ensures accurate depth control to protect work surface from overdriving
  • Integrated rafter hook for additional storage options
  • No mar tip included to keep work surface free of tool marks
  • Compatible with RIDGID Extended Capacity Magazine (AC102EM30) - Accepts two full strips of nails for increased productivity (product sold separately)
  • The included battery and charger are compatible with all RIDGID 18V Tools
  • 100% Compatible: Works with all RIDGID 18V Batteries, Tools, and Chargers
  • Lifetime Service Agreement with registration within 90 days of purchase
  • Includes: (1) R09895B Brushless 30° Framing Nailer, Rafter Hook, Belt Clip, Hex Key, No Mar Tip, (1) R87004 18V 4.0 Lithium-Ion Battery, (1) R86093 18V Charger, and operator's manual
  • RIDGID: Build for a Lifetime
  • Click Here to Shop All RIDGID Products






  • Click here for more information on Electronic Recycling Programs
  • Return Policy
  • California residents
     see Prop 65 WARNINGS

Product Information

Internet # 319621471

Model # R09895KN

Store SKU # 1007449565

Specifications

Dimensions: H 13.25 in, W 4.4 in, D 14.28 in

Dimensions

Battery Charge Time (Hours)1Nail Angle30 degree
Nail GaugeNAProduct Depth (in.)14.28 in
Product Height (in.)13.25 inProduct Width (in.)4.4 in

Details

Air Tool TypeAir NailerBattery Amp Hours4 Ah
Battery/Charger(1) 4 Ah Battery & Charger IncludedCharger IncludedCharger Included
ConditionNewCord StyleCordless
Cordless/CordedCordlessFiring ModeContact, Single Sequential
IncludedBattery, Battery Charger, FramerLoading typeStrip
Magazine Capacity1Maximum Fastener Size3-1/2 in
Minimum Fastener Size2 inMotor TypeBrushless
Multi-PurposeSingle PurposeNailer FeaturesComfort Grip, Dry Fire Lockout, Fastener Depth Control, Lithium Ion Battery, No-Mar Tip, Selectable Trigger
Number of Total Batteries Included1Power TypeElectric
Returnable90-DayTool Weight (lb.)9.1 lb
Tools Product TypeAir ToolVoltage (v)18v

Questions & Answers

105Questions
caret
Q:Will it attach framing to concrete?
by|Feb 20, 2024
1 Answer
Answer This Question

A:  Hello, Artcross - This nailer is not designed for concrete. We hope this helps! If you need further support, then call or text us at 1.866.539.1710, Monday - Friday from 9 am to 5 pm (EST), or through email when you visit us at https://register.ridgidpower.com/contact.

by|Feb 27, 2024
    caret
    Q:does this nailgun penetrate concrete easily?
    by|Feb 20, 2024
    1 Answer
    Answer This Question

    A:  Hello, Artcross - This nailer is not designed for concrete. We hope this helps! If you need further support, then call or text us at 1.866.539.1710, Monday - Friday from 9 am to 5 pm (EST), or through email when you visit us at https://register.ridgidpower.com/contact.

    by|Feb 27, 2024
      caret
      Q:How many nail sleeves can you load at one time?
      by|Feb 7, 2024
      1 Answer
      Answer This Question

      A:  Hello, David - This nailer will accept 33 nails in its magazine. We hope this helps! If you need further support, then call or text us at 1.866.539.1710, Monday - Friday from 9 am to 5 pm (EST), or through email when you visit us at https://register.ridgidpower.com/contact.

      by|Feb 7, 2024
        caret
        Q:doe it need any pneumatic oil? Or any maintenance other than refilling the air pressure in the tank when performance drops?
        by|Jan 30, 2024
        1 Answer
        Answer This Question

        A:  Hello, Sscr - This nailer doesn't need to be lubricated. Additionally maintenance information can be found starting on page 12 of the use and care manual. Please utilize the link below. We hope this helps! Use and Care Manual https://images.thdstatic.com/catalog/pdfImages/5b/5bca6706-5d87-4a7f-b0ae-d2b7624e9ba3.pdf If you need further support, then call or text us at 1.866.539.1710, Monday - Friday from 9 am to 5 pm (EST), or through email when you visit us at https://register.ridgidpower.com/contact.

        by|Jan 30, 2024
          Showing 1-4 of 105

          Customer Reviews

          4.4 out of 5
          • 4.4 out of 335 reviews
          • 87% recommend this product
          Filter by:
          Showing 1-10 of 335 reviews
          Product came in a damaged box missing parts missing the box unable to register device very unhappy with purchase
          by
          Response from RIDGIDFeb 29, 2024
          Hello, Anthony - We're very sorry to hear that you've had an issue with your order! To get assistance, please contact Home Depot's Customer Support by texting “Support” to 38698, 24 hours a day, 7 days a week, or by calling 1-800-430-3376, 7 days a week, 6 a.m. - 2 a.m. ET. We hope this helps! And if we can be of any assistance in the future, please let us know at Reviews@RIDGIDmail.com. ridgidtti
          • Verified Purchase
          I'm getting ready to frame a new shed in the...
          I'm getting ready to frame a new shed in the back yard, and wanted a battery-operated framer that would do the job,This RIDGID 18-volt 21 degree 3-1/2 inch framer was a perfect fit!! Very well made, and you get a 4.0 battery and charger with this tool, it's a Great value and no need for a compressor, can't beat that!!
          by
          • Verified Purchase
          Talk about a powerful nailer!!
          I bought this to replace my old paslode framing nailer. It used butane fuel cells. This ridgid nailer uses just a battery. I was a bit skeptical about it driving spikes into hardwood lumber on a project in my barn. To my surprise. It blew me away! This nailer can easily keep up with hose and compressor nailer. The only 2 small downsides are it is a little on the heavy side and I wish it did have a led light like other ridgid tools, but the power This nailer and speed it has far outways the rest
          by
            • Recommended
            Lifetime warranty
            This is TOOL ONLY will cost another 150 dollars for battery and charger unless you already have another RIDGID 18V battery powered tool. This framing nailer uses 30-34degree clipped head nails holding 60-70 nails. You can shoot roughly 750 nails per charge. This gun has a lifetime service agreement. It weighs a little over nine pounds without the battery so it isn't that lightweight.
            by
            • Recommended
            Great Features in Hoseless Compressed Air Nailer
            On-board air tank powers this nailer so do not have compressed air hose. The instructions state that the on-board tank pressure can be up to 125 psi. This nailer uses 30 degree nail packs (the ones with paper and 1/2 heads) so no plastic waste pieces are produced. 30 degrees allows tighter access than 20 degree nailers that have full-size heads. A hard elastomeric cover fits over the metal framing claw tip to allow use where do not want marks from metal claw tip. I have a remodel project planned where I expect to use both of these to good advantage for both rough framing and then inside. The hex key for the nailer has a secure on-board storage location that includes going around the key rather then relying on just snapping in. The handle has a switch that presses in naturally when the handle is gripped that also needs to be pressed along with the trigger to reduce the possibility of accidental firing. The nail sizes to use are described both on a label and also molded into the product so do not need to dig through the instruction manual. This device weighs more than compressed air nail guns but the hand weight is going to be the same when consider that do not need to horse around a compressed air hose. When I handed it to one of my sons who has worked in construction he commented that its weight felt good to him. I feels fine to me, too, and the balance is very comfortable.
            by
            • Recommended
            Good job
            This gun is a little heavier than my air operated one without the hose attached, so you're not saving any weight, but you are getting rid of the hose anchor. It does seem to be well made even though it is made in an Asian country. I haven't used it on a large project yet, but will be soon. There is a couple things to note. It is a 30-degree gun and at our local Home Depot there was a limited supply of nails. I wanted to try 3-1/2" nails, but they didn't even stock them. The angle will make it nice to get into some places. It has nail depth adjustment that works well and is pretty straightforward in how it works. There is a lockout when you're down to your last couple nails so you don't dry fire it. It has a rubber nose piece that you can remove and then use the jaw nose if needed. You can set it so you shoot single nails or set it for sequential nailing, and the feature is done with a slide switch and can't be any easier to use. I used 3" nails to do some nailing and it worked good. For some reason, it didn't seem to kick back as hard as my air operated one and I was nailing two 2x4" together. The 3" nails did go through with just the tip protruding and the head just under the surface. Perfect for what I was doing.
            by
            • Recommended
            This is a good nailer. Lost 2 stars due to the weight and confusing marketing
            This is a good nailer. I have the cordless nailers from Dewalt, Milwaukee and Hitachi and in terms of speed this up there with the Milwaukee and Hitachi and will fire instantly. No ramp up time. Having the cordless nailer on site worked well for me as it reduces the noise of the generator and the compressor and creates less of a hazard as far as not having to trip over any hoses. This nailer has several labels and markings that says that it is for clipped nails but it accepts Round Head Nails as well so I am not sure why it is marketed as Clipped Head Nails only. I feel that will scare people away. If you are already invested in the Ridgid line I would definitely recommend it, due to the weight you may want to use the smaller batteries and have a few extra on hand. I was able to sink nails with no problems, although the direction is not marked on the depth adjuster, if you adjust it to the left you will sink the nails deeper and if you want them proud or not as deep adjust it to the right. This does not have a dedicated power button, so to operate insert the battery and press the lower button under the trigger, a green light will come on. I noticed that after approx 10 seconds of inactivity the light will go off just press this button again to wake it up. Personally I would prefer an actual on/off button. The single fire and bump fire mode works well. You have to press the nozzle all the way in and press the trigger to fire , just like any other nozzle. Overall this is a good nailer, it is a little on the heavy side and I would like to see the weight reduced for a Gen 2 model
            by
            • Recommended
            4 found this review helpful
            Nice gun
            This completes my battery operated nail gun collection. It is a nice gun. It weighs in at about 10 pounds without the battery. That's about average for a framing nailer. It can take 2 inch to 3 1/2 inch nails. It comes with a rafter hook and a belt hook. Apparently it has a small air tank inside which you are supposed to fill up sometimes. The directions are kind of vague on this. It is supposed to shoot up to 700 nails per battery charge. Which is pretty good. Back to the air tank inside the whole point of a battery nailer is to lose the compressor. I'm not a framer but I occasionally have some wood repair on my paint jobs. I guess I'll se how long it lasts. Other than that I like it very much.
            by
            • Recommended
            RIDGID 18V Lithium-Ion Brushless Cordless 30-Degree 3-1/2 in. Framing Nailer (Tool Only)
            This is a very fine tool with a lot of power. With winter coming I am curious to see how it acts in cold weather especially nailing into frozen LVL and LSL beams. With air framing nailguns and my Paslode gas gun the nails don’t set deep enough in these beams and need to be followed with a hammer to drive them in. Otherwise in warm weather and nailing in framing lumber this gun does great and with the adjustment nails can be set perfectly. Of course, the benefits are obvious; no compressor or hoses needed and, in fact, with fully charged and extra batteries, no on-site power is required. Also, unlike gas powered nailguns, the RIDGID cordless doesn’t need to be disassembled, cleaned and lubed once or twice a year. Two negatives are the weight of the gun and the limited number of nails held in the magazine. At nearly 11 pounds with battery and nails it is more than twice that of an air powered nailgun and about 50% more than a gas gun. Eleven pounds doesn’t seem like much, but hold it over your head nailing bracing, blocking or wall sheathing. Constant reloading is an inconvenience. Building walls, installing bracing, nailing down floor, wall and roof sheathing uses a lot of nails and having to stop and reload is annoying. Gas guns have the same issue.
            by
            • Recommended
            Surprisingly low noise, quick and easy to use, no hoses to trip over!
            The RIDGID R09895B 30 degree cordless hoseless framing nailer indicates it takes Clipped Head nails but RIDGID support confirmed it can take Full Head nails as well. That's important as Clipped Head nails don't meet building code in some places. I had no problem loading or using Full Head nails making a small project to hold electric net fence for winter storage. I didn't need the included rafter hook for this little project but did like how easy it is to drop in a strip of nails and slide the pusher back to catch them and feed the driving mechanism. The minimum battery is 3 Ah but I had a 4 Ah MaxOutput that snapped in perfectly. There is a nearly invisible activation button under the ring finger of the hand grip so is instinctive to use and the trigger takes only mild pressure to nail. The tool, battery, and nails are about 10 pounds so it is a fair bit to be hanging off the end of your arm but for this project I found it very manageable. Long term use might get kind of tiring but at least you won't be dragging air hose around with you! I didn't trip over air hose once doing this first project. The tool does have a Contact mode where you hold the trigger and it nails as soon as you press the nose against the work. The Full Sequential mode better suited my use where you place the nose then squeeze the trigger to nail. I was surprised by how little noise the nailer makes compared to a pneumatic nailer and especially compared to fuel based hoseless nailers which are really loud.
            by
            • Recommended
            Showing 1-10 of 335 reviews