#1 Home Improvement Retailer

Cart

Cart

Questions and Answers for undefined

Questions & Answers

25Questions
caret
Q:What is the size diameter of the hole for the Fossett
by|Aug 18, 2020
1 Answer
Answer This Question

A:  Jose, Thanks for the question on the American Standard Evolution sink. The hole size is 1-3/8" in diameter. Your American Standard Consumer Connection Team.

by|Aug 19, 2020
    caret
    Q:What size in the center hole
    by|Aug 18, 2020
    1 Answer
    Answer This Question

    A:  Jose, ^Thanks for the question on the American Standard Evolution sink. The center hole is approximately 1-3/8" in diameter. Your American Standard Consumer Connection Team.

    by|Aug 18, 2020
      caret
      Q:Just purchased and see my studs aren't close to lining up. Is it okay to use a toggle bolt instead of the supplied hanger bolt? Thank you!
      by|Feb 11, 2020
      1 Answer
      Answer This Question

      A:  Ryan, You will need to ensure that there is adequate support to allow the sink to be fully supported. Using a toggle bolt will not likely allow enough support. Your American Standard Consumer Connections Team.

      by|Feb 11, 2020
        caret
        Q:what kind of faucet is needed for this how many inches does it have to be?
        by|Jan 25, 2020
        1 Answer
        Answer This Question

        A:  Jack, you will need a single hole faucet for the American Standard Evolution 0467100.020. Sincerely Your American Standard Consumer Connections Team.

        by|Jan 27, 2020
          caret
          Q:How large is the hole... And how wide in the rim around it
          by|Nov 29, 2019
          1 Answer
          Answer This Question

          A:  Deborah, the sink is 22" wide. If you scroll down to the info & guides section you will find the link to the product specification sheet which will show you all the available dimensions. Sincerely your American Standard Consumer Connections Team

          by|Dec 1, 2019
            caret
            Q:Is it possible to hide the water supply valves in the pedestal base?
            by|Oct 15, 2019
            2 Answers
            Answer This Question

            A:  Well, the lines are looped and visible, but the valves themselves are hidden because of the way they were roughed in. You can't "tuck" behind the pedestal, and it's hard to do the work between the pedestal and the wall (I've not done that DIY before.)

            by|Mar 15, 2023
              2 found this answer helpful

              A:  No, the pedestal base will not sit directly up against the wall, so they cannot be hidden in the base itself. Your American Standard Consumer Connections Team.

              by|Oct 15, 2019
                1 found this answer helpful
                caret
                Q:How far above floor should the center line be to hang the sink from?
                by|Jun 19, 2019
                1 Answer
                Answer This Question

                A:  If you view the specification sheet it will give you an approximation as to where the mounting screw holes should be drilled. However it is very important to follow the directions and first set the leg and pedestal up and actually mark the screw holes before you drill.

                by|Jun 27, 2019
                  caret
                  Q:Is this a small sink? Looking for a small pedestal sink. If not, what’s your smaller option?
                  by|May 13, 2019
                  1 Answer
                  Answer This Question

                  A:  JustineC, this sink is 22". Our smallest would be the Tropic Petite model # 0403.400 at 21"'. Sincerely, American Standard Tech Team

                  by|May 14, 2019
                    caret
                    Q:Is the drain a center drain ?
                    by|Mar 22, 2019
                    2 Answers
                    Answer This Question

                    A:  It's in the middle left-to-right, but back against the "wall" (flat part) front-to-back.

                    by|Oct 16, 2019
                      1 found this answer helpful

                      A:  Yes, the drain is in the center.

                      by|Oct 16, 2019
                      1 found this answer helpful
                      caret
                      Q:Wanting to go from 4” to 8” center holes in bathroom pedestal sink. Present one is American Standard and looks like 22” Evolution, but measures 21 1/4” x 18 3/4”. Are the sinks really the same?
                      by|Sep 17, 2018
                      1 Answer
                      Answer This Question

                      A:  We would need to know your current model number for sure. If you look under the sink the model number is embossed into the under. Once you have obtained the model please contact us directly through the American Standard website "Contact Us" located at the bottom of our home page so we can assist you. Sincerely, American Standard Tech Team

                      by|Mar 23, 2023
                        page 1 page 3