Questions and Answers for Rino-Tuff Universal Fit .065 in. x 275 ft. Gear Replacement Line for Corded and Cordless String Grass Trimmer/Lawn Edger

A:  it's very easy to wind onto the spool and doesn't break easily even with unexperienced people like me.

A:  Line is easy to wind onto head, but I would not recommend this line for anything more heavy than trimming soft grasses.

A:  This line is more flexible than the other 0.095" multi edge lines I have used so should be easier. I recommend Ryobi 40V battery trimmer which has a push through head which is the easiest design I have used for reloading line. One can either take off cover or just push through the new line halfway, then wind the cover and the line is sucked into the head. No messing with the actual spools and winding!

A:  Yes, if you owner's manual specifies .065 inch line. Otherwise, follow manufacturer recommendations.

A:  Yes

A:  YES........ .065 diameter is the recommended string for your trimmer. Also: YOU CAN REWIND SPOOLS BUT YOU MUST FOLLOW THE FOLLOWING PROCEDURE; REMOVE ABOUT 30 FEET OF STRING FROM THE PACKAGE. CUT THE ENDS WITH A SHARP TOOL. PUT THE ENDS (ONE IN EACH HOLE OF THE SPOOL) IN THE SPOOL, WRAP THE STRING ONTO THE SPOOL (BOTH SIDES ) BEING CAREFUL TO NOT OVERLAP THE STRING AS MUCH AS POSSIBLE. BE SURE TO OBSERVE THE DIRECTIONAL ARROW . LOOK AT THE SPOOL, THERE IS A TOP/BOTTOM SPOOL, NOW CUT THE STRING LEAVING ENOUGH HANGING OUT TO THREAD THROUGH THE HOLES., PUT THE STRING IN THE UPPER SPOOL IN THE SLOT PROVIDED, PUT THE BOTTOM STRING THROUGH THE SLOT/HOLE OPPOSITE THE TOP. INSERT SPOOL UNTO HOUSING PUTTING THE BOTTOM STRING IN FIRST,THROUGH THE HOLE IN THE CASE, KEEP THE STRING TIGHT, INSERT THE TOP STRING THROUGH THE GUIDE, KEEPING IT TIGHT. PUT THE RETAINER CAP ON. PULL THE STRINGS TIGHT, PUSH THE RELEASE BUTTON, THE STRING SHOULD ADVANCE

A:  This product has a universal fit for most corded and cordless trimmers.

A:  Yeah, this .065 diameter is compatible with most trimmers including yours

A:  I've used it with my corded string as well as gas powered trimmers and it works fine Hope this helps!

A:  Yes it should work fine.

A:  can be used on any trimmer that uses the .080 line

A:  Yes, but.... Battery powered trimmers may not have the power to spin it effectively. Read the tool's manual. It will indicate a recommended line diameter, use that size. Above assumes you know how to measure, cut and wind onto the spool. Since this is a 'bulk' line... Thicker line has more mass / inertia, therefore needs more power to spin it. In general gas trimmers use a pair of lines and battery trimmers use a single line. Also check the 'outlet' of the trimmers diameter....line has to flow smoothly through the guides...

A:  You can use this any where where a 0..080 in line is suggested.

A:  Thank you for your recent inquiry with The Home Depot. It sounds like you may need to special order your item. Please visit your nearest Home Depot Store and speak to one of our experienced associates at the Special Services desk. For any other questions, please call us at HomeDepot.com Customer Service 800-430-3376. Thank you for shopping Home Depot.

A:  home depot

A:  in the isle where the weed eaters are they sell it by the roll found mine on the bottom shelf

A:  Home Depot has it in 250 feet. The package has a built in cutter which is great and saves time.

A:  Home Depot has it. By Rino-Tuff, works well.

A:  Yes, it works fine on mine.

A:  Hi labtwo121, Yes, this Rino-Tuff .080 Trimmer Line is the same size line that the Black & Decker Grasshog is equipped with. The original spool can be reloaded with this string. Do not use a larger or smaller line because this unit is auto feed and weight sensitive to feed correctly. Thank you for asking, -Travis

A:  I did a little research and found that this string will work perfectly with the B&D GH2000 Grasshog dual auto feed.Just be sure to wind each sring in the direction shown on the spool.

A:  Yes it should fit, just remove the cap, being careful so spring doesn't pop our, remove any old sting fragment, and wind this new 0.080 Universal string on the spool, be sure to wind in the direction shown on the spool until the spool is full, then reinstall the spool with the spring in correct location..