#1 Home Improvement Retailer

Customer Reviews for DIABLO 10 in. x 60-Teeth Fine Finish Saw Blade

Internet #100033809

Model #D1060X

Store SKU #881462

  • Compatible with 10" miter saws, slide miter saws, & table saws
  • Cuts plywood, melamine, MDF, hard & soft woods
  • Little to no sanding rework required

Customer Reviews

  • 4.9
    out of 771 reviews
  • 98% recommend this product
Filter by:
Showing 1-10 of 771 reviews
Cuts smooth burrless clean cuts.
Cuts smooth burrless clean cuts.
by Punky4351
Baltic birch plywood is tough on saw blades. I use these because they last longer.
Baltic birch plywood is tough on saw blades. I use these because they last longer.
by soundpro
This is not the cheapest saw you'll find, but having tried others it is worth the money. So far I...
This is not the cheapest saw you'll find, but having tried others it is worth the money. So far I have had no burn marks, using on 3/4 Birch plywood. It cuts a very smooth line with no splinters on the bottom edge (you will always get some on the top edge but it's really minimal). This fit perfectly on craftsman miter saw.
by Minty1
First thing I do when I get a new saw is to install a new Diablo blade. I know there are more exp...
First thing I do when I get a new saw is to install a new Diablo blade. I know there are more expensive blades out there, but so far Diablo blades have never let me down. This blade was for my new table saw. I use a lot of plywood in my work and need as clean of cuts as I can, but also need a blade that can handle cross cuts on hardwoods as well. This blade does not disappoint, great cuts! This is a very reasonable priced blade that can be used for most your needs. I prefer fewer teeth for rip cuts, but I have done some with this blade and it held up pretty good there too.
by txgent10
1 person found this helpful
When compared to the factory blade that came with my table saw. This one cuts so much better with...
When compared to the factory blade that came with my table saw. This one cuts so much better with way less splintering. I also purchased them for my miter saw and circular saw.
by Papabearcraft
Installed on my Ryobi 10" Compound sliding miter saw. Cuts Great! Smooth finish and Fast! This is...
Installed on my Ryobi 10" Compound sliding miter saw. Cuts Great! Smooth finish and Fast! This is the Blade!
by Polebarnnorm
1 person found this helpful
I've been cutting 2X4's for shelves, and the cuts are very clean and easy.
I've been cutting 2X4's for shelves, and the cuts are very clean and easy.
by George
Best bang for the buck!!
I have a Delta table saw and have been using the factory blade for 6 months. As a wood worker, my products can be ruined by one bad cut. My Delta blade wasnt cutting like I needed and upgraded to the Diablo 60 tooth blade after reading all the positive reviews. might and day difference! cut fast and smooth with no tear out at all.
by American
I have the same blade that I have been using for about three years and it gets used almost daily....
I have the same blade that I have been using for about three years and it gets used almost daily. The cuts are always smooth with no tear out. I cut from pine, zebra wood, cherry, maple, olive, oak, poplar, mora and many more with no issues at all. These blades may cost more but they are well worth it in the long run. You won't be disappointed
by Picasso
19 people found this helpful
The Diablo bade is top notch. Clean cross cuts with limited tear out on all woods with proper fee...
The Diablo bade is top notch. Clean cross cuts with limited tear out on all woods with proper feed rates used.
by Ftwrthgeorge
Showing 1-10 of 771 reviews