#1 Home Improvement Retailer

Internet #204273373

Model #800252

Store SKU #254215

#8-32 Zinc Plated Machine Screw Nut (100-Pack)

$767
  • Easy to install with a wrench
  • The most widely used nuts available
  • Quick disassembly for repairs and maintenance
Store
0 in stock
Text to Me
caret

Product Details

Hex nuts are widely used in construction and to create a bolted joint. They are available with coarse or fine threads. Use with a screw or hex bolt to create a strong connection.

Additional Resources

From the Manufacturer

You will need Adobe® Acrobat® Reader to view PDF documents. Download a free copy from the Adobe Web site.
caret

Specifications

caret

Questions & Answers

4Questions
caret
Q:Is this the thread size for screws to secure a GFCI outlet to a metal cover plate? Screws normally screw into a metal box. In my case, the screws go thru the metal cover plate and thru the holes of the GFCI, then the cover plate is screwed to the box.
by|Nov 29, 2021
1 Answer
Answer This Question

A:  Most GFCI outlet will require either #6-32 or #8-32 screw size such as Everbilt #8-32 Zinc Plated Machine Screw Nut (100-Pack) to fasten.

by|Nov 30, 2021
    caret
    Q:Can these nuts be used to self-thread onto the end of an aluminum rod?
    by|Oct 26, 2021
    1 Answer
    Answer This Question

    A:  Everbilt #8-32 Zinc Plated Machine Screw Nut (100-Pack) will not self-thread onto an unthreaded aluminum rod.

    by|Oct 26, 2021
      caret
      Q:Will these nuts fit on a Stihl chainsaw cover to tighten the bar on a model 029.
      by|May 26, 2021
      1 Answer
      Answer This Question

      A:  Please check the owner's manual for the manufacturer recommendations for replacement parts.

      by|May 26, 2021
        caret
        Q:Do these nuts fit round head 1-1/4 screws as per Everbilt combo 27661?
        by|Jul 25, 2020
        2 Answers
        Answer This Question

        A:  This machine screw nut will fit the #8 x 1-1/4" round head combo machine screw.

        by|Jul 29, 2020

          A:  yes they do

          by|Jul 26, 2020
          Showing 1-4 of 4
          caret

          Customer Reviews

          4.5 out of 5
          (47)
          • 4.5
            out of 47 reviews
          • 100%recommend this product
          Filter by:
          Showing 1-10 of 47 reviews
          I make bird feeders using spoons that have been drilled and need a screw and nut to hold them tog...
          I make bird feeders using spoons that have been drilled and need a screw and nut to hold them together. Have used these for about 10 years and have never had problems. Check out the look and the bolted spoons.
          by
          • Verified Purchase
          • Recommended
          I got this to use for a new project a combination temperature and humidity control. The Everbilt ...
          I got this to use for a new project a combination temperature and humidity control. The Everbilt #8-32 tpi Zinc-Plated Machine Screw Nut is versatile and easy to work with what you can do with it is really only limited by your own imagination. This is being done as a special super review . The finished product is a combination temperature and humidity controller. it can be used for a egg incubator, exotic pet snake tank, water dragon tank, and cigar humidor, etc. The list of parts for this project are : a 15 amp duplex outlet a single gang duplex outlet cover a 1-Gang 18 cu. in. PVC Old Work Box a 2 gang decora black switch plate a 2 gang 32 cu new work box a 15 amp 120 volt 3 prong grounded 6 foot appliance cord 14 and or 16 gauge wire a wire nut for said wire 4 Everbilt #6 x 3/4 in. Zinc-Plated Pan-Head Phillips Drive Sheet Metal Screw a temperature control a humidity control red and blue spray paint painters tape, news paper. vinyl letters 2 small sets of Everbilt #8-32 tpi Zinc-Plated Machine Screw Nut with Everbilt #8-32 in. x 1 in. Truss Head Combo Zinc Machine Screw tools : black magic marker, drill, knife, flat and Phillips screw driver, wire strippers, straight edge or ruler, needle nose pliers, precision small screw driver set, multi meter step 1 : remove the mounting screws from the outlet 2] put the outlet into the the holes for the switch plate and the outlet cover, use a black magic marker to mark the mounting holes 3] drill out all of the holes so the screws will fit snugly. 4] take the outlet cover and cover 1/2 with the news paper using the painters tape and paint it red and put it aside. 5] take the back wire cover off the temp control, hold it up to the decora switch plate for each hole and use the marker to mark off the excess plastic on the left and right sides. this should be done on the back side, the wire covers are dis-guarded. 6] using the knife cut away the excess plastic so the temp control will fit into both holes snugly with out moving up or down. 7] take both box's, where they will connect together and mark a center line, the 2 gang box needs to have the mounting ears facing down. 8] measure 1 inch from the back of the 2 gang box and make a x on the center line, now measure 2 inchs up put a - and then out from each side of that - and make a x in each spot. 9] do the same to the 1 gang box 10] drill out the outer x holes so the nut and bolt combos will fit the outer holes 11] drill out the center x hole to 1/2 , 5/8 or 3/4 inch 12] on the back of the 2 gang box their is a knock out opposite the wings 13] above the knock out drill 2 holes so a sheet rock screw can fit in them but not the head. 14] pop the knock out, out, and use the knife to cut from the knock out up to the outer edges of the holes so you have a hanging hole with a slot that will hang on a dry wall screw. 15] on the inside of the 2 gang box their are wings on each side of the wire holders that need to be removed. as they stick out past the screw mounting posts they can be cut out with the knife, i did that the first few dozen times. then I started drilling the out side wing area and rip them out with needle nose pliers from the inside. this is all so the temp and humidity controls will fit. 16] the decora face plate can be placed on the front of the 2 gang box, use the screws to make sure the mounting holes line up correctly, make a line on the back of the face plate where it meets the edge of the 2 gang box on the bottom where it will connect to the 1 gang box. 17] now the top and bottom box's can be bolted together. 18] using the sheet metal sheers cut the plastic line across the bottom of the decora face plate. put it aside. 19] the power wire comes in the bottom of the 1 gang box through a wire holder and the ground from it can be screwed onto the earth ground of the outlet and so can the neutral wire. 20] the hot wire gets connected to 4x 14 or 16 gauge wires with the wire nut and they get run through the hole from the 1 gang box into the bottom of the 2 gang box 21] those 4 wires left to right connect to pin 1 solenoid supply and pin 3 power supply on both controllers, you can connect them later. the pin numbers are facing the back of the controllers 22] 2 ground wires are connected to the second screw of the neutral on the outlet and are run to pin 4 return on both controllers, for now they can be run through the hole box 1 to box 2 they are connected later. 23] break the tab connecting the 2 screws together on the outlet for the small spade hot wire 24] connect 2 wires 1 to each screw these are your feed wires they will connect to pin 2 on each unit, they can be run through the hole. 25]pry open the wire holders with a screw driver and put the humidity sensor wire in the top section and the temp sensor wire in the lower section, both in the lower wire holders of the left side facing the front of the unit. 26] take the tape off the one side of the outlet cover , reverse it and paint the other side blue. 27] take the decora face plate and with the cut side facing down put the temp control in the lower spot so the cut edge is below it. 28] using the wire strippers strip 1/4 inch off the ends of all of the wires after they have been cut to a appropriate length, remembering the extra wire goes into the bottom on the 1 gang box. 29] using the small screw drivers connect the sensor wire first to the temp control from the temp probe, then connect the rest of the wires as described above. using the multi meters beep for closed circuit function to determine which wire is which if their all the same color, the hot feed wire should go to the left side of the outlet. 30] now put in the humidity control, you can see it blocks the screw blocks on the temp control, which is why it had to be done in the correct order. now connect all of the wires as listed above and match up the sensor wires to the listed colors on the wire diagram on the control box, ignoring the rest of the wiring diagram. hot feed to right side outlet. 31] now for the real fun, carefully push the face plate with the now wired up and mounted controls into the 2 gang box, while gently pulling on the sensor wires so they are not jammed in the box and the same to all of the supply wires pulling the excess into the base of the 1 gang box under the outlet. 32] once the face plate is close enough , put in your screws and gently start tightening it so the face plate depresses into the 2 gang box. once it is behind the front of the single gang box that sits out 1/2 further then the 2 gang box your good. 33] gently squash all of the extra wire down into the single gang box so the outlet will fit in their. if your wires are too long now is the time to shorten them. 34] you can put your vinyl letters on top of the humidity and temp controls 35] if the outlet cover is dry you can mount it using its 3 screws, dont put on the vinyl letters just yet in case you reversed the feed wires. plug it in and your all set, if the feed wires are correct for function you can put on your vinyl letters. other wise just reverse the outlet cover. I developed this entire project off the top of my head, their are no blue prints or diagrams and this is the first time I have ever typed out a entire procedure of how I build them. This is how to build the combination single zone temperature with humidity control. I also build multi zone temp controls some with over temp alarms. EVERY THING beyond the temperature and humidity controls them self's was purchased at Home Depot.
          by
          • DIY
          • Recommended
          2 found this review helpful
          by
          • Verified Purchase
          by
          • Verified Purchase
          poor starting threads. obscene prices for all fasteners...
          poor starting threads. obscene prices for all fasteners
          by
          • Verified Purchase
          Good. As hoped that it would be. keep up the...
          Good. As hoped that it would be. keep up the great work.
          by
          • Verified Purchase
          Best nut I've ever had....
          Best nut I've ever had.
          by
          • Verified Purchase
          really? YOU MUST ASK ABOUT YOUR CUSTOME SERVICE - Avoid writing about customer service, contact us instead if you have issues requiring immediate attention
          really? YOU MUST ASK ABOUT YOUR CUSTOME SERVICE - Avoid writing about customer service, contact us instead if you have issues requiring immediate attention
          by
          • Verified Purchase
          by
          • Verified Purchase
          by
          • Verified Purchase
          Showing 1-10 of 47 reviews

          Frequently Bought Together

          Top Rated
          +
          +
          Price:
          $767

          Compare Similar Machine Screw Nuts

          current product
          Top Rated#8-32 Zinc Plated Machine Screw Nut (100-Pack)
          #10-24 Zinc Plated Machine Screw Nut (100-Pack)#4 to #40 Grade 18-8 Stainless steel Machine Screw Hex Nuts (100-Pack)#6 to #32 Grade 18-8 Stainless steel Machine Screw Hex Nuts (100-Pack)
          BrandEverbiltEverbiltPrime-LinePrime-Line
          Name#8-32 Zinc Plated Machine Screw Nut (100-Pack)#10-24 Zinc Plated Machine Screw Nut (100-Pack)#4 to #40 Grade 18-8 Stainless steel Machine Screw Hex Nuts (100-Pack)#6 to #32 Grade 18-8 Stainless steel Machine Screw Hex Nuts (100-Pack)
          Price
          $767
          $767
          $912
          /package
          $1102
          /package
          Ratings
          (47)
          (13)
          (0)
          (0)
          Size#8#10#4#6
          Fastener PlatingZincZincStainless SteelStainless Steel
          MaterialSteelSteelSteelSteel
          Thread pitch32244032
          Fastener Thread TypeCoarseCoarseCoarseCoarse
          Package Quantity100100100100
          View ProductView ProductView ProductView Product