White 3-Gang Duplex Outlet Wall Plate (1-Pack)

This has a very clean look. Makes your outlets look nice and without the eye sore of screws...

I like the cleaner look of these wall plates. I've always hated the look of the screws in these plates, the paint chips off of them and they end up pointing in different directions if you don't care about that sort of thing. These snap on/off of a base plate where the screws are contained and a base is attached to the wall. The snap on function of the cover plate does seem a little cheap and I fear that if you remove these more than a few times you'll end up breaking the little tabs that hold the cover on.

This review is for the Leviton Interek 4 gang screwless wall plate, # 022-80312-SW. Though it comes in assorted colors, this specific cover is white. The cover measures 8 inches long by 4 1/2 inches wide. Installation is easy. Simply remove the old cover, screw on the provided base plate and then snap on the seamless screwless cover. This screwless cover is far better looking with a modern flare than the typical stock covers, which in this case, had 8 screw heads to stare at. This is a plastic cover with steel screws, so care should be taken not to over tighten the screws, just snug them up and check for a perfect alignment. I recommend this cover to anyone wanting to dress up or modernize their cover plates.

I obtained this product because the title intrigued me... a screwless wall plate. And it turns out, while that isn't exactly true, that is exactly what it looks like after installation. The product comes put together and consists of a screwless cover that clicks onto a plastic plate that actually does screw into the receptacle box in the same places as a "screwed" wall plate. To install, the 2 plates are pried apart as the instructions on the back of the package indicate. Then the back plate is screwed onto the receptacle box. Once that is done, the top plate is pressed onto back plate and clicks onto it. The installation was easy and the plate came off easily as well although I went very carefully when taking it off just to be sure that I didn't break anything. Once off, the top plate again snaps easily back onto the back plate. The product comes with 6 screws. They were too short for my application, so I used the screws that I had previously used with the screwed wall plate. If your receptacle box is perfectly installed which mine weren't, they will work fine. Otherwise you may have to purchase some screws to make this work for your installation. They could have come with longer screws and that is why I made them a 4 star instead of a 5 star. Once installed, they look nice. The corners are not quite as rounded as the screwed wall plate.

Leviton's Decora Plus Screwless Wallplate goes on quickly and makes a huge difference. The visual noise and clutter that is cut out with the elimination of those six screw heads is much more pronounced than I thought it would be. The clean edge looks fantastic. The plastic is nicely molded and the fit is perfect. I am very pleased, and highly recommend a quick, easy, affordable upgrade.

Very good quality and has a really nice clean look, sans the screws. I didn't expect it to be two pieces. To install, screw the base piece to the tiny screw holes (very fast and simple / shallow screws) in the receptacles and then click the cover plate onto the base piece. The base piece assists greatly in aligning the paddle switches properly, which can be a problem with 3-switch panels. Definitely recommend.

Purchased this to replace a Leviton Preferred 3 Gang Faceplate. I wanted a faceplate that didn't butt up right against the wall. Noticed that this had a smaller footprint so I decided to pick one up. Pros: Simple Instructions Smaller footprint than Leviton Preferred Faceplate Nice clean look without screws showing Cons: Subplate did not sit properly on top of the Leviton Switches. Once plate was snapped into place, I noticed gaps between the wall and the plate.

Wow! Looks great! What a difference...This wall plate turned my average looking switches into a modern conversation piece. Easy to install. Just remove the old plate cover. No need to remove the switches. Just screw the new plate cover base ontothe existing switches and then snap the plate cover on top. It's that easy. It only took me a few minutes to install...and that included the time to find my screwdrivers. I recommend opening the packaging carefully so that you don't tear the instructions off (which are the back of the package).

These Decorate 3- Gang Screwless Wall Plate, White Are great to have on hand. You never know when your going to remodel your home. A good electricition has all kinds of things in his inventory for future use, We are constantly changing thing in my home,just like everyone else. No need to stop a project to run to the store and get an item. Great item

Excellent assembly and perfect finish