Q:Can this be used to repair/seal a low point with ponding on a tar-and-gravel roof?
by|Jan 30, 2024
1 Answer
Answer This Question
A: BKMom, Henry 885 TropiCool 100% Silicone would not be the product to use on a tar and gravel roof. You could use Henry 204 to repair the area as long as you apply the 204 to the surface when it is dry. Of course you will have to remove the gravel before making the repair. Just follow the instructions illustrated on the can label for a 3-course patch.
by|Jan 30, 2024
Q:Can this product be stored after opening and partial usage?
by|Jan 28, 2024
1 Answer
Answer This Question
A: Michael, after opening the container, try to use it up as soon as possible. 885 is a moisture cure product that will draw water molecules out of the atmosphere to cure. Because of this, the sealant will start wanting to cure as soon as it is exposed to the atmosphere. For smaller jobs you can use Henry 884 that comes in a caulking tube.
by|Jan 29, 2024
Q:At the Home Depot, I see product with this number , 885, but a different label that says the roof has to be dry to use it and it says seam sealer not wet patch. Is this the right product for me to patch a silicone roof that is wet?
by|Jan 22, 2024
3 Answers
Answer This Question
A: No, don't use this on a wet roof. I did it earlier this month, and it didn't stick. I gave it a one star rating. The photo shows the strips I pulled off the roof.
by|Jan 29, 2024
1 found this answer helpful
A: Yes, this is the product you need.
Mike
by|Jan 23, 2024
A: Tccc, about a year ago we changed the formula for Henry 885 TropiCool 100% Silicone sealer to make it a Wet Patch. You will need to look for the can that says Wet Patch on it to use it in wet conditions.
by|Feb 5, 2024
2 found this answer helpful
Q:Can you use Henry's tropical stop leak around your fireplace on the roof where the roofing meets the brick flute.
by|Jan 19, 2024
1 Answer
Answer This Question
A: Donald, you can use Henry 885 TropiCool 100% Silicone around chimneys between the roofing material and the brick. The service temperature of Henry 885 is from -40 degrees to 180 degrees. Henry 885 has great adhesion to a wide variety to surfaces.
by|Jan 19, 2024
Q:Can I use sanded deck coat on top of this product?
by|Jan 18, 2024
1 Answer
Answer This Question
A: Mike, since we have not tested Henry 885 TropiCool 100% Silicone with deck coat we can only say that you will have to test the adhesion of the deck coat to it. Traditionally most products will not adhere to Henry 885 except Henry 887 TropiCool 100% silicone roof coating.
by|Jan 18, 2024
Q:Can I use this Henry 885 to seal coat my entire roof? My (rubber torch down) roof leaks somewhere, but I can’t figure out where it’s getting in, so I’d like to coat the entire roof with sealant… Will this work? Or is there something better?
by|Jan 18, 2024
1 Answer
Answer This Question
A: Natalya, you could do that but it would be extremely expensive. A flat roof will generally leak in only a few places, an obvious hole, along a seam, where water stands for longer than 48 hours or where there is a roof penetration such as a vent or skylight. Your best bet would be to inspect the roof at those areas, patch any areas that look questionable with Henry 885 and then coat the roof with Henry 887 TropiCool 100% Silicone roof coating.
by|Mar 25, 2024
1 found this answer helpful
Q:I have a flat asphalt roof with Henry 887 coating, should I use 209XR or 885 to stop water leaks?
by|Jan 7, 2024
1 Answer
Answer This Question
A: Zhao, you should use Henry 885 TropiCool 100% silicone to repair water leaks if the roof is coated with Henry 887. Henry 209XR contains solvents and is not compatible with Henry 887.
by|Jan 7, 2024
Q:I'm building a roof-top garden and have root barrier that's 4-feet wide. I'm hoping to seal the overlapping seams of the root-barrier with this. I believe the root barrier is made out of polyethylene. Will this adhere to HDPE / Polyethylene?
by|Jan 6, 2024
1 Answer
Answer This Question
A: Fishtacos, we have not tested Henry 885 for use on Polyethylene. Your best bet would be to perform several adhesion tests prior to proceeding with your project.
by|Jan 7, 2024
Q:Can I thin this product
by|Jan 4, 2024
1 Answer
Answer This Question
A: Charly, Henry 885 TropiCool 100% Silicone Wet Patch is made to be used directly out of the can. It should be the consistency of a thick cake frosting. Henry 885 should not be thinned.
by|Jan 5, 2024
Q:Can tropic-cool be used on styrofoam and vinyl?
by|Jan 3, 2024
1 Answer
Answer This Question
A: Rudy, Henry 885 TropiCool 100% Silicone can be used on roofs with a spray polyurethane foam surface. For styrofoam and vinyl surfaces you would need to do an adhesion test to see how well the product sticks. To test the adhesion apply the 885 and let it cure thoroughly for 48 hours. Then pull one end to test the adhesion strength.