Q:Can this sink be undermounted with a laminate counter top?
by|Apr 9, 2020
2 Answers
Answer This Question
A: You could do it, but it might not look very good. You'd have to cut your hole in the laminate, not sure if you can round the corners. Then you'd have the underlining particle board or MSD showing which you'd need to seal, and cover up if you want.
by|Apr 9, 2020
A: Hi Wally, we do not recommend installing any under mount kitchen sink with a laminate top.
Let us know if you have any other questions by calling 1-800-775-0703 or emailing us at customerservice@kraususa.com
by|Apr 9, 2020
Q:What does zero radius mean?
by|Mar 8, 2020
2 Answers
Answer This Question
A: Hi Sheila, Our Pax Zero Radius sinks feature 90 degree corners for a sleeker modern look, whereas our other sinks feature more rounded corners and less tight bends. Please feel free to call us at 1-800-775-0703 or email customerservice@kraususa.com if you have any more questions.
by|Mar 9, 2020
A: Zero radius sinks have boxy appearances and defined corners. It refers to the four corners on the inside of the sink. Each corner is a perfect, sharp 90-degree angle, allowing for a modern, fresh look that fits with any contemporary space.
by|Mar 9, 2020
Q:What is the difference between this PAX sink and the similar PRO sink that is available with the same specs?
by|Feb 25, 2020
2 Answers
Answer This Question
A: Nonclue
by|Jun 25, 2021
A: Hello, thanks for reaching out. Without knowing the other model specifically I can't tell you the difference between that and this one, but if you would like to discuss the differences you can email us at customerservice@kraususa.com or email us at 1-800-775-0703. We look forward to hearing from you!
by|Aug 3, 2020
Q:Can sink be ordered with additional 1 hole for hot water dispenser? If not, can it be cut on own readily?
by|Feb 24, 2020
1 Answer
Answer This Question
A: Hi Ann,
Thank you for your question!
The sink cannot come ordered with an additional hole but we do sell other sink models that come with a second perforated hole option, such as the KHT411-25.
We do not recommend cutting into the steel as it may jeopardize the integrity of the sink.
If you have any more questions or concerns please do not hesitate to reach out to us at 800-775-0703, and we will be more than happy to help!
by|Feb 24, 2020
Q:what are the actual dimensions of the bowl?
by|Feb 23, 2020
1 Answer
Answer This Question
A: Hi Joseph, thanks for your question! The bowl measures 13"x16" for more dimensions see the spec sheet from our website: https://www.kraususa.com/pub/media/catalog/product/documentation/KP1TS15S-1-Sink-Spec-Sheet.pdf
Feel free to call us at 1-800-775-0703 or email us at CustomerService@KrausUSA.com if you have any other questions.
by|Feb 23, 2020
Q:I just ordered this Kraus kitchen sink. What stainless steel cleaner would you recommend?
by|Feb 13, 2020
2 Answers
Answer This Question
A: Hi Joanne,
Thanks for reaching out to us and congratulations on your new sink!
Using standard soap and water would be just fine to clean your sink. Also, products such as Bar Keeper’s friend and a fine 3M Scotch Brite pad are both great options for the care and maintenance of your new stainless steel sink.
Hope this helps.
Please feel free to reach out to us at 800-775-0703 or email us at customerservice@kraususa.com with any additional questions.
Happy to assist.
Best regards,
Mike
Kraus USA
by|Feb 14, 2020
A: We use Dawn dish cleaner. Never used a stainless on it yet. Great sink, only complaint my wife does not like to secure the drain secure because it has a specific direction even though its square. You are going to love it . It is big so don't let your contractor tell you it can't be installed perfect. It takes a little extra work .
by|Feb 14, 2020
Q:Is a 33 inch as above available with a side drain instead of a center drain?
by|Feb 6, 2020
1 Answer
Answer This Question
A: Thank you for your question!
Unfortunately, with the Pax sinks we do not currently have a model with an off-set drain.
You may be interested in the KCH-1000 which is also available through The Home Depot, and is an exclusive that offers a right-set drain.
If you have any questions please to do not hesitate to reach out to us at 800-775-0703, or at cusstomerservice@kraususa.com
Thank you for your time
Kraus USA
by|Feb 7, 2020
Q:Gentlemen:
I need to get a Bottom Sink Grid for the
KRAUS Pax Zero-Radius 18.5in. 18 Gauge Undermount Single Bowl Stainless Steel Kitchen Sink, Silver as above and I can not find it any where ....Could you refer me to a store or website???
by|Feb 5, 2020
1 Answer
Answer This Question
A: Hello, thanks for reaching out. At the moment we do not make a bottom grid for that sink so none are available. I will pass your feedback on to our product development team, I apologize for any inconvenience.
by|Jan 6, 2021
1 found this answer helpful
Q:What is the cutout dimensions for the sink? We are replacing an existing sink so what to make sure existing cutout will work.
by|Jan 30, 2020
1 Answer
Answer This Question
A: Hi GMS,
We recommend a minimum cabinet size of 36" for our KP1TD33S-2 and also recommend using the cardboard template that is included with the sink for cutting your counter top as the radius of the corners will need to be factored into the cut. We also have DXF (CAD) files available directly on our website. We can also email it to you or your fabricator directly if you would like.
Please feel free to reach out to us at 800-775-0703 or email us at customerservice@kraususa.com with any additional questions.
Happy to assist.
Best regards,
Kraus USA
by|Jan 31, 2020
Q:What size is the hole diameter on this sink?
by|Dec 3, 2019
1 Answer
Answer This Question
A: Hi Mare,
Thanks for reaching out out. Our Kitchen sinks offer a standard 3.5" diameter drain hole.
Please feel free to reach out to us at 800-775-0703 or via email at customerservice@kraususa.com with any additional questions.
Happy to assist.
Best,
Mike
Kraus USA