Questions and Answers for Panasonic WhisperChoice AutoPick-A-Flow 80/110 CFM Ceiling Bathroom Exhaust Fan with Motion/Humidity Sense and Flex-Z Fast Bracket

A:  The fan needs to have constant power, control wall switch is optional and it’s not included.

A:  I just wired it to the wall switch. Any controls are in the unit (Humidity, Speed, motion sensor)

A:  This fan has two different issues, The fan staying ON all the time is most likely set at a low RH relative humidity, the RH Dial should be set at 80%, if is set at 50% or lower the fan will not turn OFF. The second issue, is caused by high air restriction, caused by the way the duct was installed or by the EZ Bracket being installed incorrectly. Please give us a call at 866-292-7299 option 1 then option 2 for further assistance.

A:  Sounds like your damper is closed check to see if it is working . You can adjust settings for 2 minutes like I did and also you can change moister setting , I left mine at the manufactures setting . Hope this helps . Good luck

A:  Did you make sure that the tape was removed from the baffle in the duct adapter? If the baffle cannot open the fan will not exhaust the air from the room. See image below from installation instructions.

A:  This issue is caused by high air restriction, caused by the way the duct was installed or by the EZ Bracket being installed incorrectly. Please give us a call at 866-292-7299 option 1 then option 2 for further assistance.

A:  Drop the cover down and remove it. You’ll see two switches that you can use to adjust the settings.

A:  To adjust the humidity (RH) & TIMER (delay) remove the grill you will find the adjustments there. There is no adjustment for the motion sensor other than TIMER which is the delay before the fan turns back off if there’s no motion & the humidity is below its setting (we recommend 80%).

A:  I'm suggested to drop the cover down, but how do I go it? Is there an instruction video?

A:  You can adjust how long it stays on by removing the cover - and turning the run-time knob. There is a separate adjustment for run time when high humidity is detected.

A:  To be able to get support for you Vent Fan, please reach out to the Panasonic Customer Service for Vent Fans during 9AM - 6PM (EST) Monday through Friday via Phone: (866) 292-7299, or via Fax: (888) 553-0723. You can also Email them at: ventfans@us.panasonic.com .

A:  Hello! We would be more than happy to assist you further! Please contact us directly at https://na.panasonic.com/us/iaqsupport with more information about your inquiry. -M

A:  To be able to get support for your Vent Fan, please reach out to the Panasonic Customer Service for Vent Fans during 9AM - 6PM (EST) Monday through Friday via Phone: (866) 292-7299, or via Fax: (888) 553-0723. You can also Email them at: ventfans@us.panasonic.com .

A:  I wired mine off a GFCI plug, because it is close to the shower and as the instructions recommend. At the last minute, I put it on a switch so I can keep power off while wiring and not have to run down to the circuit braker. The instructions don't mention to put it on a switch (as best as I can remember). I would recommend putting it on a switch. I turn mine off in the winter because I want the moisture in the space. Of course it doesn't work when the switch is turned off.

A:  Directly wired , no on/off switch. If power Is off the sensors will not work.

A:  Hi Em, thank you for your recent inquiry with The Home Depot. I believe the best advice would be to talk to one of our specialty department professionals at your local Home Depot store. For any other questions, please visit your nearest local Home Depot store. We appreciate your business and look forward to serving you in the future. Thank you for shopping Home Depot.

A:  To be able to get support for your Vent Fan, please reach out to the Panasonic Customer Service for Vent Fans during 9AM - 6PM (EST) Monday through Friday via Phone: (866) 292-7299, or via Fax: (888) 553-0723. You can also Email them at: ventfans@us.panasonic.com .

A:  You need to leave the wall switch on for it to work as an automatic motion sensor or humidity sensor.

A:  Strictly motion and moisture. I put mine on a switch to regulate when this goes on. I don't need it to run in the winter.

A:  To be able to get support for your Vent Fan, please reach out to the Panasonic Customer Service for Vent Fans during 9AM - 6PM (EST) Monday through Friday via Phone: (866) 292-7299, or via Fax: (888) 553-0723. You can also Email them at: ventfans@us.panasonic.com .

A:  I've connected my fan to a wall switch which works fine. Actually the motion detector doesn't see to work for me.

A:  To be able to get support for your Vent Fan, please reach out to the Panasonic Customer Service for Vent Fans during 9AM - 6PM (EST) Monday through Friday via Phone: (866) 292-7299, or via Fax: (888) 553-0723. You can also Email them at: ventfans@us.panasonic.com .

A:  I have two units as well. Both work at 80 and 110 CFM. But what doesn't work for me is the Motion detector or humidity detector.