Questions and Answers for WILD BADGER POWER 26 cc 2-Stroke 2-in-1 Gas Full Crank Straight Shaft Grass Trimmer with Brush Cutter Blade and Bonus Harness
Q:With the brush blade the vibration is horrible! Has anyone discovered how to reduce the vibration? Did I put the blade on incorrectly? I mean there is only one way to put it on because it is reversible, correct? Full throttle is a killer!
by|Jul 25, 2022
4 Answers
Answer This Question
A: If you can hang on to it at full throttle it hurts your hands and it starts to vibrate WAY before then. Badger says NOT to use any other blade. It'll take a heavier line than the .095 it comes with, so I'm gonna try that.Copy & paste the following for suggestions: https://opereviews.com/size-string-trimmer-line-use/
by|Aug 18, 2022
A: i had to center and tighten the blade with a rachet. one it was on good and tight i had no issue with extra vibration. it is a beast and blew thru my 1/4 acre of brush.
by|Aug 23, 2024
2 found this answer helpful
A: No the blade has been put on correctly the vibration will vibrate your arms off of your torso.
by|May 9, 2023
1 found this answer helpful
A: You might not have the blade centered, checkit ,, when on correctly it's very balanced.
by|Jul 19, 2024
3 found this answer helpful
Q:Can the brush blade be turned upside down when blade gets dull?
by|Jun 29, 2022
1 Answer
Answer This Question
A: It would work but this would not be the preferred method use this cutter
by|Jan 5, 2023
Q:Does Cutting Head Or Blade Rotate Clockwise With Debris Thrown To The Right, Or Opposite ?
by|Jun 6, 2022
1 Answer
Answer This Question
A: Hi. It rotates clockwise as it should and throws to the right. Hope this helps.
by|Mar 11, 2024
Q:blade plastic or steel ?
by|Dec 24, 2021
7 Answers
Answer This Question
A: Steel
by|Dec 27, 2021
A: Steel
by|Dec 27, 2021
A: Comes with both a steel blade and a plastic string cutter. However I would not recommend this product. I've had mine for less than a year and it is very difficult to start already.
by|May 7, 2023
A: Steel
by|May 2, 2024
A: Steel. Very nice product. I use to clear brush and saplings, starts easy every time. Very fuel efficient.
by|Jun 17, 2022
1 found this answer helpful
A: The included blade is steel, as are any replacements.
by|Nov 21, 2023
A: Steel
by|Dec 27, 2021
Q:Can I buy the extended warranty after I purchase the weed eater?
by|Sep 20, 2021
1 Answer
Answer This Question
A: Hello yarddog,
Thank you for your recent inquiry with The Home Depot for the 26 cc 2-Cycle 2-in-1 Gas Full Crank Straight Shaft Grass Trimmer with Brush Cutter Blade and Bonus Harness. Yes the HDPP can be purchased within 90 days of purchase with proof of purchase. We appreciate your business and look forward to serving you in the future.
by|Sep 22, 2021
Q:will it cut a 1/2 inch sapling? 3/4 inch? I have another cutter but the blades don't cut through much bigger than a 1/4 in weed. Need a sharp blade that is universal.
by|Aug 1, 2021
2 Answers
Answer This Question
A: Its about the sharpness of an ax blade out of the store. 1/2" sapling I would say yes, 3/4" may be pushing it
by|Jun 8, 2022
1 found this answer helpful
A: I believe that you would have to change the blade to one with like a circular saw blade to cut brush that size. I changed mine and it works very well.
by|Jul 19, 2024
1 found this answer helpful
Q:Will the Badger brush cutter cut underwater. Looking to cut some Lilly pads and Cat tails around the edge of the pond.
by|Jul 30, 2021
1 Answer
Answer This Question
A: Hi DB.....The metal blade should work fine in your application. I would recommend that you disassemble the two joining members of the shaft and give it a good shot of WD40 before and after the chore.
by|Jul 30, 2021
Q:If it can use the chain saw blade, how big are the sapplings it can cut?
by|May 8, 2021
3 Answers
Answer This Question
A: Hi Smitee.....The blade is not a chain type blade but a circular blade. I've cut samplings up to 1-1/2".
by|Aug 8, 2021
1 found this answer helpful
A: As big as the saw blade, minus a few inches really
by|May 8, 2021
A: There is no chainsaw blade.
by|Aug 16, 2021
1 found this answer helpful
Q:Does the brush blade have a "right" orientation? Should the printing on the blade be visible from above or below (or does it matter)?
by|Apr 23, 2021
4 Answers
Answer This Question
A: Yes it does.
by|Jul 23, 2021
A: It doesn’t really matter for the blade but in practice, I always face the sticker out/down on blades
by|Apr 24, 2021
A: Hi Elysium.....The printing on the blade should be facing towards the unit.
by|Apr 24, 2021
A: You should see the printing on blade while holding tool. Arrow goes to motor rotation.