Coating strength held perfectly through brick masonry.
by
Verified Purchase
Apr 10, 2024
by
Verified Purchase
Apr 10, 2024
Associate helped me find exactly what I needed.
by
Verified Purchase
Apr 10, 2024
Performed as promised in a cinder block wall !
by
Verified Purchase
Apr 10, 2024
Carbide Tip went dull after three holes drilled in concrete. Had to purchase a diffent carbide bit to finish job.
by
Verified Purchase
Apr 10, 2024
I find the bits do not last. I had a bit from a few years back that was hardly used and it struggled to cut into brick. Disappointed.
by
Response from ITW BrandsApr 11, 2024
Hi there, thank you for sharing your feedback. We are sorry to hear that your experience with our Drill Bits did not match your expectations and did not work for your project. Please feel free to call us at (800)222-6990 or email us at CS@itwbrands.com. We’d like to learn more about the concrete you were trying to penetrate and make things right.
Verified Purchase
Apr 10, 2024
Worked great! I used it without hammer drill and still performed well.
by
Verified Purchase
Apr 7, 2024
This Bit was easy to use, however, it did not last as I was expected.
by
Verified Purchase
Apr 5, 2024
by
Verified Purchase
Apr 3, 2024
No problem using the bit.
by
Verified Purchase
Apr 3, 2024
by
Verified Purchase
Apr 3, 2024
by
Verified Purchase
Apr 3, 2024
by
Verified Purchase
Mar 28, 2024
Well I hope it was because of an inadequate drill (I do not own a rotary hammer drill) because it took me at least a half hour to drill one 1 1/2" hole depth.
by
Response from ITW BrandsMar 28, 2024
Hi there, thank you for sharing your feedback with us! We are sorry to hear that your experience with our product did not match your expectations. For best results, please use our three step process: pre-drill a hole using the recommended Tapcon Carbide-tipped drill bit, clean out the hole, and then drive your anchors in. Please feel free to call us at (800)222-6990 or email us at tapcon@itwbrands.com, if you followed these steps and you are still having the same issues.
Verified Purchase
1 found this review helpful
Mar 27, 2024
I managed to drill 8 holes for tapcon screws in a concrete porch to install handrails before it broke.
In the drill bits defense I also destroyed three more bits before I gave up on the entire project.
by
Response from ITW BrandsMar 28, 2024
Hi there, thank you for sharing your feedback with us! We are sorry to hear that your experience with our product did not match your expectations. For best results, please use our three step process: pre-drill a hole using the recommended Tapcon Carbide-tipped drill bit, clean out the hole, and then drive your anchors in. Please feel free to call us at (800)222-6990 or email us at tapcon@itwbrands.com, if you followed these steps and you are still having the same issues.
Verified Purchase
Mar 27, 2024
by
Verified Purchase
Mar 27, 2024
by
Verified Purchase
Mar 27, 2024
by
Verified Purchase
Mar 27, 2024
Way better than anchor s to use in cement block
by
Verified Purchase
Mar 27, 2024
Just right with the blue screws
by
Verified Purchase
Mar 27, 2024
Hex heads strip too easily.
by
Verified Purchase
Mar 27, 2024
by
Verified Purchase
Mar 27, 2024
WASTE!!!
Attempted to use two separate brand new Tapcon screw bits to drill hole into brick for Tapcon screws. DO NOT BUY. Neither drill bit did much drilling
by
Response from ITW BrandsMar 27, 2024
Hi there, thank you for sharing your feedback with us! We are sorry to hear that your experience with our product did not match your expectations. For best results, please use our three step process: pre-drill a hole using the recommended Tapcon Carbide-tipped drill bit, clean out the hole, and then drive your anchors in. Please feel free to call us at (800)222-6990 or email us at tapcon@itwbrands.com, if you followed these steps and you are still having the same issues.
1 found this review helpful
Mar 25, 2024
Not up to the task
Not including taking breaks to minimize a hernia risk, I probably spent 30 minutes and two bits drilling one pilot hole, and I'm not even sure I'm done yet.