A: The gun model DWFP 12233 can use 5/8 inch to 2- 1/8 inch long 18 gauge brad nails.
by|Sep 29, 2019
Q:will this work with Hardie plank siding and trim? I'll probably get a framing gun additionally
by|Sep 11, 2019
4 Answers
Answer This Question
A: I think it should work. Practice on a scrap piece first. You can adjust the power, if it doesn't go in far enough or to far.
by|Sep 13, 2019
A: Yes I think it would do fine for that it will drive 2” nails all the way into a 2X 4 no problem
by|Sep 16, 2019
A: I would not advise using the Brad nailer for the siding and trim I would use hot dipped galvanized nails. But the compressor is a great buy and the Brad nailer works great for light interior finish work.
by|Sep 12, 2019
A: Yes high cfm
by|Oct 17, 2019
Q:how long of Brad nails does it shoot
by|Sep 4, 2019
2 Answers
Answer This Question
A: The DWFP12233 will use 18 GA Brad Nails in sizes 5/8"-2-1/8".
by|Feb 27, 2020
3 found this answer helpful
A: Is the regulator Gauge of this item (DeWalt DEWALT 6 Gal. Heavy-Duty Pancake Electric Air Compressor) same as clock face type on the picture, instead of turn knob type?
by|Nov 27, 2020
Q:This compressor will be capable to handles a nailer for fences? If it is capable which nailer do I have to use?
by|Jun 30, 2019
4 Answers
Answer This Question
A: First you have to figure out what size nails you need for your fence. Then find a nail gun that will fire the right size nails. Then make sure the specs of the compressor match the nail gun. Sometimes the nail gun will list the minimum compressor requirements.
by|Jul 2, 2019
A: Yes it is capable running pretty much any nail gun you wish to use.
by|Sep 12, 2019
A: I wouldn’t use nails for a fence I would buy a Dewalt 1/4” cordless driver from Home Dept and use torks head screws it will be stronger and last a lot longer
by|Jul 7, 2019
A: I use exterior screws. You would need a framing nailer with treated nails to prevent rust.
by|Nov 11, 2019
Q:Is this nail gun come withcase
by|Jun 24, 2019
5 Answers
Answer This Question
A: No, it does not come with a case.
by|Jun 25, 2019
A: No case I bought soft cover carrying bags for all my nail guns three in nails that I usually need they work great. plastic cases won’t hold up over time
by|Jun 25, 2019
A: No case. If you buy the brad nailer separately, it comes with a case.
by|Jun 25, 2019
A: A case for the nail gun is not included.
by|Jun 26, 2019
A: No, the nail gun does not come with a case. However, the gun is light weight and easily transportable in a small backpack or similar carrying case.
by|Jun 27, 2019
Q:I purchased this DeWalt 18 Guage Brad Nailer and Pancake Electric Compressor Combo Kit, and it ca...
by|Jun 6, 2019
5 Answers
Answer This Question
A: U will not need any special fittings for the 3/8. All the ends are the same as far as plugging into compressor or any type of air tool.
by|Jun 8, 2019
1 found this answer helpful
A: Yes, you can use the 3/8 with this air compressors and brad nailer. The 3/8 just makes it easier to wind up. You would also need to find a 3/8 NAP IM brass female plug to attach to your 3/8 air hoes.
by|Jun 8, 2019
A: That hose should work fine with the same connections you will have more volume of air but the same amount of pressure as the 1/4” hose
by|Sep 16, 2019
A: The size of the hose changes but the size of the connection remains the same. So no.
by|Jun 12, 2019
A: You dont, the size of the hose changes, the size of the connections remain the same.
by|Jun 12, 2019
Q:I’m planning on putting shiplap on my wall, would this be good for that?
by|May 25, 2019
5 Answers
Answer This Question
A: Yes it works for shiplap. I used it for the same thing.
by|May 29, 2019
A: In my opinion, this setup would work fine since it shoots the equivalent to finish nails..
by|Jul 30, 2019
A: Yes you could use the 15 gauge nail for thin ship lap 3/4 thick or less
Make sure you are hitting studs remember you have the board and drywall thickness to get through then enter the stud min 3/4
by|May 26, 2019
A: Would work perfect.
by|Jun 12, 2019
A: Yes this product is perfect for that job
by|Jun 2, 2019
Q:As a DIYer, if I were to buy only ONE compressor for all my shop needs (trim, workbench framing, painting) would this be the one? What size should I get?
by|Apr 16, 2019
1 Answer
Answer This Question
A: The DWFP55126: 6GAL 165PSI Max Pancake Compressor is great for use with most pneumatic tools.Please check with the air tool manufactures for specifications on what compressor will work best for you.
by|Sep 5, 2020
Q:Can I spray textured with this compressor
by|Apr 16, 2019
4 Answers
Answer This Question
A: Please contact the texture gun manufacture for specifications on what will work best with their tool.
by|Apr 16, 2019
A: Yes
by|Nov 11, 2019
A: I am sure it will work but you might have to wait for pressure to build back up since it’s only a 6 gallon tank
by|May 1, 2020
A: Yes of course
by|May 26, 2019
Q:Will a framing gun work with this compressor
by|Apr 7, 2019
5 Answers
Answer This Question
A: Yes it goes to 150 psi
by|May 26, 2019
A: I would think it would work fine as it has a 6gal. air tank. It works great with the nail gun in the package. The compressor had no problem keeping up with installing Crown Molding & Floor Trim.
by|Apr 8, 2019
A: Yes has more than adequate pressure to fire a framing gun but may / may not be able to keep up with the demand if you shoot in succession rapidly.
by|Jul 30, 2019
A: Yes, there is more than enough pressure for a framing gun.
by|May 14, 2019
A: The manual states that DW45RN DeWALT framing nailer requires 3.7 CFM @ 80 psi. The DeWALT pancake compressor has a flow rate of 2.6 CFM @ 90 psi.