Questions and Answers for Delta Multi-Choice Universal Tub and Shower Valve Body Rough-In Kit

A:  Thank you for your question, HughesHomeImprovements! The Delta MultiChoice Universal Tub and Shower Valve Body Rough-in Kit with Screwdriver Stops is Model Number R10000-UNWS. Any Delta valve including the "WS" or "With Stops" designation will also offer Screwdriver stops directly at the valve. Best regards, Edward

A:  Unable to answer 1 & 2. Regarding #3. Will the water still come out when I turn it to hot even if the water has not warmed up yet (for some reason it takes several minutes for the hot water to reach my faucets & it won't heat up unless the water runs until the hot water comes out). Answer: The temperature of the water in the pipe closest to the valve is what you are going to get until the hot water in the heater reaches the valve. You may want to consider a recirculating pump so hot water is immediately available at the farthest faucet from the hot water heater.

A:  Yes but you should install integral stop valves on each side first or you'll have to put shut-off valves on the supply lines in an accessible place in order to conform to the plumbing code.

A:  Hi, you will need to access all of the tubing in order to either solder or thread them into this valve. if you already have this body... you may be able to remove the 'inards' and switch that part.

A:  It can be provided you have access to the existing valve body from the wall behind the tub/shower so that it can be replaced. Installation of this valve body requires either brazing existing or new rigid copper piper to the valve body, or installing adapters if pex piping is installed. It is much more involved than just unscrewing the existing valve body and replacing with this one. I hope this helps.

A:  The existing trim should match as long as the valve is the same as the one you are replacing. Ensure the model numbers match before you remove existing valve.

A:  I'm not sure if it was necessary but think so (we had a plumber do it)

A:  You must use the delta multichoice valve if you are installing a delta trim kit. If you have a different valve/cartridge (for example, a hans grohe cartridge) then the delta trim kit will not work correctly(if at all).

A:  If this is for a shower or bath tub it is necessary. It allows the hot and cold water to mix so when it comes out of the spout you can adjust it to the temperature you desire. If I'm not mistaken, it also prevents temperature fluctuations when you are taking a shower and someone in the house turns on the hot or cold water.

A:  No it is not necessary. You won't have to get involved with plumbing OR showering.

A:  New or replacement installation - yes as it controls all of the water flows - replacing shower head or tub spout then no as your old one is already in place - replacing tub/shower surround then no assuming you keep old controls

A:  The valve has to match the fixture, so you need a delta compatible valve to use Delta fixtures.

A:  This will work for either tub or shower only or both - just plug the side you do not need - I used for shower only

A:  Hello Gofastman, Thank you for your question. We would be more than happy to help you with this. Please feel free to call, email, or message us on social. Best regards, Tanya Phone: 1-800-345-3358 | Email: customerservice@deltafaucet.com | Facebook/Twitter: @deltafaucet

A:  When I bought the valve, the only other item I needed to complete the installation was the faucet.

A:  Thank you for your question, Dick. The cartridge will be included with the 13/14, 17, or 17T series trim kit that you purchase rather than the valve body. Best regards, Tanya Phone: 1-800-345-3358 | Email: customerservice@deltafaucet.com | Facebook/Twitter: @deltafaucet

A:  This is just the diverter. The valve must be purchased separately. The title is confusing and i had the same question.

A:  This does not come with cartridge.

A:  You need both.

A:  Hi, RFK! Thank you for your question. The bonnet nut on the Delta R10000-UNBX Rough In Valve Body can be removed by soaking a towel/washcloth in a solution of 50% white vinegar and 50% water mixture and wrapping the soaked towel around the bonnet to loosen any hard water or corrosion at the bonnet. We would be more than happy to help you with this. Please feel free to call, email, or message us on social. Best regards, Rosanna Phone: 1-800-345-3358 | Email: customerservice@deltafaucet.com | Facebook/Twitter: @deltafaucet

A:  Hi, AA. Thank you for your question. All our Delta Monitor and TempAssure Valve Trim Kits will work the Delta MultiChoice Universal R10000-UNBX Rough In Valve Body. Also, each trim kit includes the valve cartridge assembly. Here is a link to the trim kits: https://www.homedepot.com/b/Bath-Bathroom-Faucets-Bathtub-Faucets/Delta/Wall-Mount/N-5yc1vZcd07Zg2Z1z17kjf Best Regards, Rosanna

A:  Call Delta customer service. They can give you the product part number that will fit inside the valve housing.

A:  Call Delta - they have always been responsive to my calls

A:  This looks like Delta MultiChoice Universal Tub and Shower Valve Body Rough-In Kit model #R10000-UNBX which does not include a cartridge. The blue and white cartridge, Model # RP19804, is for Delta single handle tub faucets manufactured prior to 2008. Believe you will need the gray and white cartridge if your rough-in-kit is model #R1000-UNBX, and make sure that the cartridge is compatible in your existing faucet that you are apparently planning on reusing.

A:  Hi, Jav. Thank you for your question. The RP19804 valve cartridge assembly does not fit into the Delta MultiChoice Universal R10000-UNBX Rough In Valve Body. We would be more than happy to help you with this. Please feel free to call, email, or message us on social. Best regards, Rosanna Phone: 1-800-345-3358 | Email: customerservice@deltafaucet.com | Facebook/Twitter: @deltafaucet