Q:What is the minimum gap or pipe cutout to utilize this. Or, how far does it extend from pipe end when fully slid onto the slip side?
by|Jan 3, 2023
2 Answers
Answer This Question
A: It should have a minimum distance. On other words, if I do not cut my pipe by 2 inches maximum distance, is it okay if I cut by a distance less than 2 inches, for example 1 inch or 1/2 inch or even lower?
by|Mar 28, 2024
A: Hi, The SharkBite 3/4 in. Push-to-Connect Brass Slip Coupling does not have a minimum distance. The maximum amount of pipe that can be removed is 2". If you would like to discuss the installation of the SharkBite 3/4 in. Push-to-Connect Brass Slip Coupling in your application you can call tech support at 877-700-4242. (Kind regards,)
by|May 27, 2023
1 found this answer helpful
Q:I?m trying to replace a leaking copper coupling which is just at 2?. Can I cut out a tad more that 2? inches?
by|Dec 16, 2022
1 Answer
Answer This Question
A: Hello, please contact our Technical Support team at 877-700-4242 for assistance regarding your application. Regards,
by|Aug 22, 2023
Q:Can you confirm this will work for 1/2 cpvc plastic pipe?
by|Oct 29, 2022
2 Answers
Answer This Question
A: Have only used it on pex and copper tubing.
by|Oct 31, 2022
A: Hi, The SharkBite 1/2 in. Push-to-Connect Brass Slip Coupling can only be used with copper or CPVC pipe. I've attached a link to our website that also states thus information. If you have any more questions you can call tech support at 877-700-4242. (https://www.sharkbite.com/us/en/brass-push-to-connect/fittings/couplings/brass-push-slip-coupling) (Kind regards,)
by|Oct 31, 2022
Q:Dose the sharkbite work on a Copper air line?
by|Jul 26, 2022
2 Answers
Answer This Question
A: Hi, The SharkBite 1/2 in. Push-to-Connect Brass Slip Coupling can not be used in pneumatic applications. If you have any more questions you can call tech support at 877-700-4242. (Kind regards,)
by|Jul 27, 2022
A: It works excellent in copper pipe and I have used it with copper pipe where the flow is water and not air and it has not liquefied. I don't know if it works well for air. But in copper pipe this fitting works excellent.
God bless you
Angel
by|Jul 28, 2022
Q:Can you remove the 1inch sharkbite and reuse it?
by|Jul 26, 2022
2 Answers
Answer This Question
A: Yes you can. It requires strong fingers or an inexpensive tool. Just press against the connection and slide the shark it’s off the pipe.
by|Jul 27, 2022
A: Hi, The SharkBite 3/4 in. Push-to-Connect Brass Slip Coupling can be removed and reused based on several factors. If you would call tech support at 877-700-4242 we would be happy to discuss this with you. (Kind regards,)
by|Jul 27, 2022
Q:will it work on baseboard copper heat pipe
by|Jun 20, 2022
1 Answer
Answer This Question
A: Hi, The SharkBite 3/4 in. Push-to-Connect Brass Slip Coupling Fitting will work on radiant heating applications. It has been tested up to 200 degrees Fahrenheit. If you have any more questions you can call tech support at 877-700-4242. (Kind regards,)
by|Jun 27, 2022
Q:Says copper or cpvc...no pex?
by|Apr 28, 2022
3 Answers
Answer This Question
A: Hi, The SharkBite 1/2 in. Push-to-Connect Brass Slip Coupling Fitting is not compatible with PEX pipe. If you have any more questions you can call tech support at 877-700-4242. (Kind regards,)
by|Jan 18, 2024
1 found this answer helpful
A: Works on pex too I’ve used several in my house my whole house is cpvc and pex
by|May 1, 2022
A: I only used it on copper.
by|Apr 30, 2022
Q:Is the disconnect clip included?
by|Mar 7, 2022
5 Answers
Answer This Question
A: I think it was. However, with a small screwdriver it is dead easy to pull the ring back and pull the brass fitting.
by|Mar 9, 2022
A: No.
by|Mar 9, 2022
A: No
by|Mar 9, 2022
A: Hi, The SharkBite 1/2 in. Push-to-Connect Brass Slip Coupling comes with a disconnect clip. If you are in need of help picking a mixing valve you can call tech support at 877-700-4242. (Kind regards,)
by|Mar 7, 2022
A: no
by|Mar 9, 2022
Q:will this work on soft copper
by|Feb 17, 2022
2 Answers
Answer This Question
A: It may work if the copper has the same pipe OD and ID with the sharkbite/PEX pipe. But please don’t quote me on this as I have not tried it with soft copper.
by|Feb 25, 2022
A: Hi, The SharkBite 1 in. Push-to-Connect Brass Slip Coupling will not work with soft copper. If you have any more questions you can call tech support at 877-700-4242. (Kind regards,)
by|Feb 18, 2022
Q:Would a pair of 3/4" 45 Deg fittings work for a 1" offset? If not, any suggestions.
by|Feb 2, 2022
1 Answer
Answer This Question
A: Hi, We will need more information about your application in order to provide assistance. If you are still needing help you can call tech support at 877-700-4242. Kind regards,