Customer Reviews for Avanti 5-1/2 in. x 100-Tooth OSB/Plywood Circular Saw Blade

Cuts plywood like butter. Ryobi circular saw. (Used for the straight edges) brought plywood from 48 to 40 inches

Plywood edges are coming out really rough with this blade. The photo is showing a cut with a Diablo 60 tooth fine finish blade on the top, and this plywood blade on the bottom, on the same work piece. On the positive side, I had no ripouts with this blade, it's cheap, and it's been cutting quite a bit of plywood, so if the edges are not exposed, this may work fine.

A good blade will do all the work for you, that's what this AVANTI 5 1/2-inch x 100 tooth OSB/ plywood circular blade saw does, cuts through wood like butter, easy to use and change, very well made!!

Great for my home improvements.

Absolutely the best blade. Cut through butcher block countertops like butter

It cuts osb really well I will try plywood in a few days a very good blade for the money

I used with my ryobi cordless saw. Cut over 500 square ft of flooring and cut excellent cuts . Pergo restoration oak flooring. have had my saw for many many years. The new blade made my saw like new again.met all my expectations.

Used this in cordless saw to cut 1/4" hardwood plywood. This blade provided a fine cut. I will also be using this blade to cut tuftex panels.

They say you get what you pay for... bought this today for my (brand new) Ryobi 18v one 6.5" circular saw... 1st cut through scrap 1/2 plywood it began to burn up. I forced it through, but gave up halfway through the 3rd cut. swapped to my 7.25" crapsman circular saw with a 140 tooth black and decker blade that is over 5 years old and has seen plenty of use. the black and decker didn't even think twice. before you start blaming the saw, it is brand new (also bought it today) and yes, the batteries were charged. it was cutting through old hand milled maple 2x stock like butter with the 24 tooth blade it came with 15 minutes earlier

I was going to have H.D. cut my beadboard wall paneling I just purchased. But they said their big industrial saw jig thingy would just chew it all to pieces. After reading on-line I realized I needed a fine tooth replacement blade for my circular saw to cut the beadboard. I checked many stores on line and to my amazement Home Depot had this blade for a ridculously low price. I figured for that price if it didn't work out - no big deal. To my surprise it cut the beadboard like butter. I was thrilled! The picure is of the leftover pieces, as the big part I used is covered up by an armoire, but you can see the perfect cuts.

I bought this Blade for Cutting 1" thick Acrylic. It worked perfectly, I used it on my 20V Dewalt Circular saw.

Worked for the job I had to do at the time. It was perfect for plywood without any splitting.

Cut smoothly through ground contact wood for a deck frame. I look forward to trying on another project.

Unusual use for this blade, I used it to cut metal roofing to length.worked great

Blade ripped through 3/4 inch sanded plywood flawlessly. Great blade for the money. Only used it for one project so we'll see how the edge holds up, but for home use it is a good blade.

used this blade on a Ryobi cordless 18V skilsaw to cut 1/8" thick 4'x8' sheets of wainscot panel board, zipped right thru no problems. do be careful of which side is facing up during cutting as cutting with finish side up can result in chipping of paint, cutting finish side down left a clean cut on finish face without chipping the coating,

I rarely purchase plain steel circular saw blades, as carbide lasts much longer. But I rarely cut particle board, and bought the least expensive blade available. I was surprised to find that after many cuts, this blade was still very sharp, and the last cut was as smooth as the first!

It does cut however after being made to fight making about 60 cuts through OSB 1/2 inch it was apparent this isn't a blade made for heavy duty use. I ended up buying the Diablo 5 1/2 inch Blade & was much happier with the purchase. I wouldn't recommend this blade when there are SO much better blades out there for about the same cost!

This blade has a real smooth cut. I bought this blade to cut some plexiglass (Lexon) & it really did a great job, without splintering.

Blade was exactly what I needed and as described.

Blade was perfect for cutting vinyl lattice for a shed skirt.

It cut my plywood very good and is steel sharp

great price and is good for occasional use

Put flooring in my shed cut the plywood 4 cuts already dull