#1 Home Improvement Retailer

Questions and Answers for Edsal 5 ft. Butcher Block Workbench Top

Internet #204422916

Model #BB3060

  • Made with kiln-dried maple strips
  • Assembles easily to compatible Edsal workbench
  • Ideal for tool, die and electrical wiring work

Questions & Answers

183Questions
caret
Q:Is it heat resistant enough to withstand boiling water temperatures? say around 200-250 degrees?
by|May 25, 2018
2 Answers
Answer This Question

A:  Yes, I have a couple of dry mount presses and they get over 200 degrees sometimes and the table never gets more than a little warm and dissipates the heat quickly.

by|Dec 2, 2019

    A:  I will say yes, but the main thing is to have the butcher block sealed well. I used Tung oil and my wife has been putting hot pots on there and had no problems, I keep telling her to put a pot holder down first. Hope that helps

    by|May 5, 2023
    caret
    Q:What is involved to add wheels to the legs
    by|May 16, 2018
    2 Answers
    Answer This Question

    A:  Adding wheels to the legs is a DIY tweak that I cannot advise or explain in detail for you. Thanks.

    by|Feb 21, 2020

      A:  Can’t be done. You need different legs.

      by|Feb 21, 2020
        1 found this answer helpful
        caret
        Q:Can you attach a vise to this workbench
        by|Feb 21, 2018
        2 Answers
        Answer This Question

        A:  Yes, and it should be bolted into place, not just screwed down. Mike

        by|May 5, 2023

        A:  Yes

        by|Jan 29, 2020
          caret
          Q:Where can I find a tool chest that will fit under this workbench?
          by|Jan 13, 2018
          0 Answer
          Answer This Question
          caret
          Q:Can it work without putting on the bottom shelf. And removing the bottom shelf would it affect t...
          by|Jan 7, 2018
          5 Answers
          Answer This Question

          A:  Not using the shelf would make the workbench unstable.

          by|Jan 22, 2019

          A:  The bottom shelf is part of the support system for the bench. I would not recommend not using it.

          by|Jan 22, 2019

          A:  I would not do that, I don't think it would be stable enough without it. My big problem is the particleboard top. I bought two workbenches but had to send one back it was so battered.

          by|May 5, 2023

            A:  no, it lends stability to the table.

            by|May 5, 2023

              A:  I would recommend using the bottom shelf. It is part of the support system.

              by|Jan 23, 2019
              caret
              Q:Does this table fold up for storage?
              by|Jan 6, 2018
              10 Answers
              Answer This Question

              A:  This does not fold for storage.

              by|May 5, 2023

                A:  Nope.

                by|May 5, 2023

                  A:  This table does not fold up.

                  by|Jan 22, 2019

                  A:  No this table does NOT fold up for storage.

                  by|May 5, 2023

                    A:  No!

                    by|Jan 22, 2020

                      A:  No its bolted together as a sturdy workbench

                      by|Aug 13, 2019

                        A:  no

                        by|May 5, 2023

                          A:  No

                          by|Jan 14, 2020

                            A:  Yes if you can one that is not damaged. It only took me three tries before I got one I could use.

                            by|Sep 2, 2019

                              A:  No, it is a ridged assembly. also, I added lock-washers, when I assembled mine. I'm using it as a base for a wood lathe, and it holds up to the vibration very well, very stable. Very happy with the quality.

                              by|May 5, 2023
                                caret
                                Q:What are the inside dimensions?
                                by|Jan 6, 2018
                                2 Answers
                                Answer This Question

                                A:  The shelf dimensions are 60" x 30" (W x D).

                                by|May 5, 2023

                                  A:  20 7/8" x 54 3/4" and roughly 20" from the top of the bottom shelf ridges to the bottom of the table top frame. I would NOT recommend putting something heavy on this bottom shelf.

                                  by|Nov 19, 2018
                                    caret
                                    Q:Can I get this item any sooner than November 14?
                                    by|Nov 6, 2017
                                    1 Answer
                                    Answer This Question

                                    A:  Hi Scott. The only way to have this item sooner will be to locate a store in your area that has this item in stock. Go to our website and enter in your zip code in the store search box “Check Nearby Stores” and you will be able to find any stores within 100 miles of you that have this item in stock. Otherwise, it will have to be done thru our website. Please let us know if we can be of further assistance. Rick_HD_OC

                                    by|May 5, 2023
                                    caret
                                    Q:Can you add casters to the legs easily?
                                    by|Oct 12, 2017
                                    5 Answers
                                    Answer This Question

                                    A:  no

                                    by|May 5, 2023

                                      A:  Sorry, the legs are sheet metal formed in a "V" shape for strength. You would have to add something to the bottom to mount the casters to.

                                      by|Nov 19, 2018

                                        A:  This unit is designed to be stationary, adding casters would create an unstable work platform.

                                        by|May 5, 2023

                                          A:  NO. The bottom of the 'legs' are nothing more than bent sheet metal, with NO method to mount casters without SIGNIFICANT DESIGN MODIFICATIONS. I had hoped to do the same, but....

                                          by|Dec 19, 2018

                                            A:  No. There isn't a hole to easily add casters.

                                            by|Feb 11, 2020
                                              caret
                                              Q:Product is what I need but height has to be 38 inches. Do you have anything 84-90 inches long that is 38 inches high?
                                              by|Sep 16, 2017
                                              0 Answer
                                              Answer This Question