Questions and Answers for RYOBI Bi-Metal Impact Rated Screwdriver Drill Bit Kit (50-Piece)

A:  This set's smallest bit (in the shortest length) is a size #0. You also have all sizes up to #3 in the kit. If you are fastening decking, I'd recommend you use the longer bits in the kit. Typically the specialty fasteners also have bits in them. But this set will have you covered with pretty much any size you end up selecting for your project. The SQ1 designation you mentioned is the size, which is a square #1.

A:  I have been using my kit since I picked it up Everything that I used work very well.

A:  Thank you hisbanded for your question. SQ0 is the smallest bit in the RYOBI 70-Piece kit .~hope this helps with your selection, Ashley

A:  If your using a deck screw more than likely you’ll need SQ2 or 3 SQ1 is more for a finish screw or trim screw

A:  No

A:  I have used mine to put a metal roof on our porch and metal braces in the walls. I am extremely satisfied.

A:  No

A:  Hi Shem, These are screwdriver bits so the surface it is used on would not matter. Thanks for asking. Greg

A:  This is a driver kit the surface doesn't matter it depends on the screws which should tell you on the box but i would not recommend that you use these on masonry

A:  No

A:  Not sure of your question--these bits are for screws and hex nuts/bolts, not for chiseling or masonry work.

A:  It's best if you have a rotary hammer and drill a hole and then put some tapcons in those tapcon in.but those bits will screw in tapcon bits

A:  These are not Drill Bits.

A:  ?

A:  Hi Dave, The bits in this kit are for screws and bolts and would not work for bricks. Thanks for asking. Greg

A:  Should be compatible

A:  Hi Ema, This kit will work with the Ryobi 18v drills. Thanks for asking. Greg

A:  I haven't had compatibility issues with them going from 3 different drills and an electric screw driver.

A:  YEAUH

A:  yes any 1/4 hex driver

A:  Used them with a 20 year old standard Black and Decker. Worked fine.

A:  YEAUH!!!

A:  yes

A:  Yes

A:  Hi Emalinda, This kit will work with the Ryobi 18v drills. Thanks for asking. Greg

A:  I do admit its a little trickier than it should be, with the box oriented clear side up an the green tab with the arrows to the right, using your right thumb, push the top of the green tab to the right to un latch the clear cover, then try to catch the upper right corner of the clear plastic cover with a fingernail from your left hand... The cover really should have a tap to pull up on!

A:  No problems opening this plastic case very easy to use and nice selection of bits.

A:  I used scissors

A:  The locking mechanism is a bit counter-intuitive. It feels like it should be on a hinge and "flip down," but it's just a release lever. Just pull/bend the lock to the right with your right thumb and lift the clear lid to the left with your left thumb.

A:  Hi Claire, The latch on the side lifts make sure there is not a wire tie left on where the latch is. Hope this helps. Greg

A:  Yes it works greats

A:  Yes they will.

A:  I had an isssue with the original clasp. They replaced the whole set immediately.

A:  90 days at store with receipt or proof of purchase, Warranty: This product is a consumable item. Therefore, it is warranted against defective parts and labor only and not from misuse or deterioration of the product through normal wear and tear.

A:  Return the set to home depot and they should replace it.

A:  I am very satisfied with the set, it was just what I needed

A:  This product is a consumable item. Therefore it is warrantied against defective parts and labor only and not from misuse or deterioration of the product through normal wear and tear.

A:  Hey there. The DockIT system is being phased out the majority of new bit kit​ (70pc. included) will not be compatible. Thank you!

A:  No, it is not compatible.

A:  Don’t know what a Dock Holder is but I did use various extensions. The shortest extension was about 2 inches in total length the longest extension was 12 inches to reach screws in the very back of the shelving. Shelving was both wood and metal. The screws were buried in the wood and very hard to back out. The screws were rusted in place and took a lot of pressure to remove. The bits worked well. No wear and tear.

A:  No idea what a Dockit holder is? It comes in its own case.... I just googled what a Dockit holder is, and I would say it is highly likely it will fit, but check with Ryobi as they make both.

A:  ya, i got my kit about a month ago it's great!

A:  Absolutely. I use them interchangeably between drill and driver. That is why i purchased this set.

A:  Yes, they are stronger for use on an impact driver and will work fine on a regular drill. Mike

A:  Generally speaking, yes by all means, provided it was a variable speed drill.

A:  Yes, it mentions that in the accompanying video.

A:  Hey Ash, yes, you can. Practically all of our bits are compatible with standard drills. However, if you were to use an impact driver, you would need to make sure the bit has a hex shank. Thanks!