#1 Home Improvement Retailer

Questions and Answers for Powermate 105 - 135 psi Pressure Switch

Internet #202592803

Model #034-0226RP

Store SKU #1000529142

Questions & Answers

27Questions
caret
Q:The small line, believe it is called the bleeder, is a male connection. Is the switch shipped with the female connector and ferrule. can i get one
by|Jul 16, 2016
2 Answers
Answer This Question

A:  The unloader valve has the opening for your plastic line with a keeper washer inside. I just cut the plastic line clean and inserted it in a was done.

by|Apr 7, 2017

    A:  This pressure switch is shipped with a 1/4" bleeder vlv which has push to connect fitting. It does not require a ferrule.

    by|May 3, 2023
      caret
      Q:does it come with all the tubes or just the switch itself? Thanks
      by|Jul 10, 2016
      2 Answers
      Answer This Question

      A:  Just the pressure switch with the unloader valve attached

      by|Apr 7, 2017

        A:  Only the switch itself along with plugs. There is no tubes included.

        by|May 3, 2023
          caret
          Q:Is the pressure adjustable mine is a 95 on 125 off ? Thanks
          by|Jul 8, 2015
          2 Answers
          Answer This Question

          A:  Yes! The switch has a single screw adjustment under the cover that allows you to adjust the shut off pressure, but the turn on pressure is preset at 30psi below the turn off pressure. So you would just need to adjust it!

          by|Jan 9, 2021

          A:  Unfortunately you cannot adjust the setting on a pressure switch. However, Powermate offers another pressure switch with a factory set at 95-125 PSI. The Part Number is E103952, Please contact Powermate Product Service by dialing 888-895-45495 for more information.

          by|May 3, 2023
            1 found this answer helpful
            caret
            Q:what voltage can this switch handle?
            by|Jul 6, 2015
            2 Answers
            Answer This Question

            A:  Mine is 120 hot and common and ground

            by|Apr 7, 2017

              A:  You can use this pressure switch at either 120 or 240 volt.

              by|May 3, 2023
                3 found this answer helpful
                caret
                Q:I run a Long Term Care Pharmacy and our upright 65 gallon compressor is used all day and 1/2 the night in packaging our medications. I really don't have the time to wait till one can be shipped next week or so. I can fix anything myself if I have the parts.
                by|Feb 27, 2015
                2 Answers
                Answer This Question

                A:  Unless you can find the pressure switch locally, you will need to order the part. Please dial 800.628.8815 for further assistance.

                by|May 3, 2023

                  A:  You can order a spare to keep on your shelf. Kinda weird that you need to replace it so often. .

                  by|Jan 9, 2021
                  caret
                  Q:what is the pipe size
                  by|Jun 9, 2014
                  1 Answer
                  Answer This Question

                  A:  The four ports on the bottom of the switch are 1/4”-18 NPT, and the bleeder is 1/4” O.D. tube w push to fit connection. Thanks, Bryan customercare@matholdingsinc.com

                  by|Apr 18, 2019
                  1 found this answer helpful
                  caret
                  Q:My new switch cuts off at 135 PSI OK but once it does so it starts to bleed compressed air from the black small plastic elbow in the bottom of the switch until l it reaches 105PSI then it clicks in again, so if i leave the compressor switch on ( wall switch ) it keep recycling like this way and i cannot get a steady pressure as well as waste of power and noise please advise
                  by|Apr 1, 2014
                  2 Answers
                  Answer This Question

                  A:  Sounds like bad switch Id ask for a replacement

                  by|Apr 7, 2017

                    A:  Hello, We are very sorry to hear of your trouble with this pressure switch. We would like talk to you further. Please email customercare@mathold.com with your contact information and the best way to reach you. Thank you! Customer Care

                    by|May 3, 2023
                    caret
                    Q:i need a pressure switch compatible to a Condor - 4 Port Side Wire Feed (MDR21-EA/11). 100/125 psi. i have seen the ones homedepot carry but i can't figure out which on i can use.campbell hausfeld has one #cw208700av. but can't wait a week for to arrive. here are pictures of the one the i need. thank you so much
                    by|Nov 24, 2013
                    1 Answer
                    Answer This Question

                    A:  Hello, Thank you for your questions. A pressure switch that has similar specs is the 034-0150. This switch is a 4 port single phase switch that kicks in at 95 out at 125, has front wiring, a side bleeder vlv, see FLA & LRA ratings below. Volts FLA LRA 120V 24 144 240 24 80 Please contact your local home depot store for more assistance. Thank you! Karyn from Customer Care

                    by|May 2, 2023
                    caret
                    Q:What is the amp rating on this device
                    by|Mar 11, 2013
                    2 Answers
                    Answer This Question

                    A:  Hello, Please see the below ratings: 034-0226RP FLA RATING 26A – 240V, LRA RATING 156A – 240V Thank you for your question!

                    by|May 2, 2023
                      6 found this answer helpful

                      A:  I'm using it on a 13 Amps Motor at starting demand sometimes reaches 25 amps.

                      by|May 2, 2023

                        Frequently Bought Together

                        +
                        +
                        Price:
                        $32.43