Return this item within 90 days of purchase.
Get an answer now with AI
Magic Apron Assistant is an AI virtual assistant. By proceeding, you consent to the recording and use of your information by The Home Depot (and authorized third parties). More information
BrassCraft 1/2 in. Nominal Push Connect Inlet x 3/8 in. O.D. Compression Outlet 1/4-Turn Straight Valve controls water flow to household plumbing fixtures. The straight valve is most often used where the water pipe enters the room from the floor. With a 90° turn of the valve handle, you are able to stop the flow of water leading to the plumbing fixture, allowing for maintenance and repair without shutting off the water to the entire home. Push Connect valves are installation ready requiring no special tools, soldering or glue for a watertight seal.
Inlet Diameter (In.) | 1/2 |
|---|---|
Outlet Diameter (In.) | 3/8 |
Product Length (in.) | 2.25 in |
Application | Potable Water |
|---|---|
Color/Finish | Silver |
Compatible Pipe Material | Copper |
Compatible Product | Faucet, Ice Maker, Other |
Connection | PTC x Comp |
Features | Lead Free |
Indoor/Outdoor | Indoor, Outdoor |
Material | Brass |
Maximum Pressure (PSI) | 125 PSI |
Maximum Working Temperature (F) | 160 |
Pack Size | 1 |
Returnable | 90-Day |
Valve Configuration | Straight |
Manufacturer Warranty | Limited Manufacturer Warranty |
|---|
No this stop will not work for you. The OD of 3/8" nominal PEX-B piping is 1/2". The outlet of our water stop is 3/8" OD compression. We offer a G2CR34X C1 which has a 1/2" OD compression outlet. Please note when using compression fittings on PEX you will need to use a tubing stiffener inside the tubing at the compression connection.
I think that the answer provided by BrassCraft may be in error as the G2CR34X requires a 1/2" Nominal connection which is 5/8" OD. The initial question was for a 1/2" OD copper pipe, which is the equivalent of a 3/8 Nom. Am I in error?
Compression water stops can work with 1/2" nominal PEX piping but only when using a stainless steel tubing insert. The BrassCraft part number would be a TS-8X. Do not use compression on PEX piping without the insert. The other options would be depending on your type of PEX piping- expansion PEX, crimp PEX or push to connect. If you need more information, please contact technical support at 877-272-7755. Thanks
Compression water stops can work with 1/2" nominal PEX piping but only when using a stainless steel tubing insert. The BrassCraft part number would be a TS-8X. Do not use compression on PEX piping without the insert. The other options would be depending on your type of PEX piping- expansion PEX, crimp PEX or push to connect. If you need more information, please contact technical support at 877-272-7755. Thanks
Compression can be used on PEX tubing but it will require a 1/2" nominal PEX tubing stainless steel insert (tubing stiffener). The BrassCraft part number for the insert would be TS-8X. You could also use a PEX A (expansion PEX) or PEX B ((crimp PEX) specific stop or a push to connect water stop. If you need more information, please contact technical support at 877-272-7755. Thanks
Yes! 1/2" nominal compression would be the same as 5/8" OD compression.
No, this valve is not approved for direct connection to polybutylene tubing. Polybutylene installations require a transition fitting specifically designed for polybutylene pipe. The valve shown is intended for use with 1/2" copper, CPVC, or PEX tubing that meets the product specifications. RA
The primary concern is preventing heat from reaching adjacent solder joints during valve replacement. A qualified plumber can typically desolder and replace the valve with elbows located only a few inches away by using appropriate heat shields, heat-blocking compounds, or wet rags to protect nearby connections.
A refrigerator water line is 1/4" OD compression. We do not offer a 1/4" OD compression X 1/4" OD compression water stop. You could use a OR07X C1 (SKU# 247917) 1/2" FIP X 1/4" OD compression outlet with an adapter on the inlet- Part number: 68-4-8X - 1/2" MIP X 1/4" OD compression adapter to connect to the existing 1/4" OD compression ice maker line. Thanks
Viewing 1-8 of 183
4.7 out of 5